EDmini v2 in Wake-on-LAN limbo

Ethernet disk mini v2
Post Reply
ruben
Posts: 9
Joined: Sat Aug 28, 2010 4:24 pm

EDmini v2 in Wake-on-LAN limbo

Post by ruben » Sat Sep 04, 2010 1:35 pm

Ok, I can kick myself :oops: .

As I mentioned previously I would experiment with Wake-on-LAN.
So I checked the uboot sourcecode from the Lacie GPL tarball.
It mentioned in ./board/mv88fxx81/Common/mvCommon.c:282 that byte 8 is set to zero to enable WoL.
Now, I did :D, and now my box waits for a WoL packet, but I appear not to send the correct magic sequence.
Moreover, it doesn't seem to react to the buttonpress, while it should according to the sourcecode :? ./board/mv88fxx81/Common/mvCommon.c:386

Code: Select all

Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 400Mhz 
SysClock = 133Mhz , TClock = 166Mhz 

USB 0: host mode
USB 1: device mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Power Button Released
	Sleep Mode & WOL
egiga0 no link
Waiting for WOL Magic Packet
Using egiga0 device
Any suggestions whatsoever to get passed the WoL limbo :D?

rosbif
Posts: 112
Joined: Thu May 08, 2008 11:23 am
Location: near Toulouse, France

Re: EDmini v2 in Wake-on-LAN limbo

Post by rosbif » Sat Sep 04, 2010 6:07 pm

ruben wrote:Any suggestions whatsoever to get passed the WoL limbo :D?
Maybe CLUNC will do the job.
CLUNC is a netconsole that you can get here.
If this doesn't work, Albert (aaribaud) will probably know the solution.
Or try asking on the lacie-nas mailing list ;-)

ruben
Posts: 9
Joined: Sat Aug 28, 2010 4:24 pm

Re: EDmini v2 in Wake-on-LAN limbo

Post by ruben » Sun Sep 05, 2010 12:49 pm

Clunc doesn't seem to work either :(

I'll post to the mailinglist later today or tomorrow. (or ping aaribaud? :) )

rosbif
Posts: 112
Joined: Thu May 08, 2008 11:23 am
Location: near Toulouse, France

Re: EDmini v2 in Wake-on-LAN limbo

Post by rosbif » Sun Sep 05, 2010 1:02 pm

ruben wrote:I'll post to the mailinglist later today or tomorrow. (or ping aaribaud? :) )
I'd recommend trying the list (lacie-nas@sequanux.org).
Albert is subscribed: he posted yesterday ;-)

rosbif
Posts: 112
Joined: Thu May 08, 2008 11:23 am
Location: near Toulouse, France

Re: EDmini v2 in Wake-on-LAN limbo

Post by rosbif » Sat Sep 11, 2010 6:15 am

rosbif wrote:I'd recommend trying the list (lacie-nas@sequanux.org).
This discussion continued on the lacie-nas mailing list.
Anyone interested can read it here.
AIUI the problem was worked around by resetting the 8th byte of the I2C EEPROM to 0xFF using an external programmer (but with the EEPROM in situ).
The conclusion is "don't mess with the 8th (WOL) byte of the EEPROM until the real problem is understood" :(

Post Reply