failed update from 4.61 to 4.62 (NSA310)

Marvell Kirkwood based
Post Reply
patrolpl
Posts: 1
Joined: Sat Nov 16, 2013 9:24 am

failed update from 4.61 to 4.62 (NSA310)

Post by patrolpl » Sat Nov 16, 2013 9:35 am

Firstly i've tried to do an auto update over WAN. Then get the messege that update has failed. After that i've downloaded file manually and send it over LAN - still failed. I rebooted my NSA310 and it didn't load properly - power led was flashing and flashing...
So I connect via serial and...
"/zyxel/mnt/nand/sysdisk.img.gz: No such file or directory" it doesn't sound good.

any ideas?

Code: Select all

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Feb 22 2011 - 10:31:35) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFEE0

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net:   egiga0, egiga1 [PRIME]
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x4640000, size 0xa00000

Reading data from 0x503f800 -- 100% complete.
 10485760 bytes read: OK
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2013-03-27   8:44:10 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6061900 Bytes =  5.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux...........................................................................................................................................................................
............................................................................................................ done, booting the kernel.
Linux version 2.6.31.8 (root@Neo) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #2 Wed Mar 27 16:43:46 CST 2013
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 65024
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2
FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 244608KB available (5300K code, 300K data, 3164K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1199.30 BogoMIPS (lpj=5996544)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
PEX1_MEM ....no such
PEX1_IO ....no such
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- RD-88F6281A  Soc: 88F6281 A1 LE

 Detected Tclk 200000000 and SysClk 400000000
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected Link X1
pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:01.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
gpio_dev = fd00000
LED_SET_CTL_IOC_NUM= 6702
High gpio polarity = 50
High gpio polarity = 70
Enable Interrupt
mv88f6281_wdt: Watchdog Timer timeout = 8 sec.
mv88f6281_wdt: HW Watchdog timeout    = 15 sec.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 478
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
Wake up disk0......
Wake up disk1......
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
EnablePowerSaving
PowerSavingTime = 15
No found HD
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 0 Giga ports supported
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload (TSO) supported
  o Large Receive offload (LRO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Network Fast Processing (Routing) supported - (Disabled)
  o Driver ERROR statistics enabled
  o Proc tool API enabled
  o SKB Reuse supported - (Disabled)
  o SKB Recycle supported - (Disabled)
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):

mvFpRuleDb (c8dee000): 2048 entries, 8192 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 77 at 0x0000009a0000
Bad eraseblock 728 at 0x000005b00000
9 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 9 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
hwmon-vid: Unknown VRM version of your CPU
lm85 0-002e: Starting monitoring
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2013-11-16 09:07:47 UTC (1384592867)
Freeing init memory: 3164K
*** Stage 1: Setup system and device drivers ***
usb 1-1: new high speed USB device using ehci_marvell and address 2
In hub_port_init, and number is 0, retry 0, port 1 .....
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
r8168 Gigabit Ethernet driver 8.023.00-NAPI loaded
r8168 0000:00:01.0: no MSI. Back to INTx.
 Set LED ...
eth%d: RTL8168B/8111B at 0xd0900000, 00:00:00:00:00:30, IRQ 9
r8168: This product is covered by one or more of the following patents: US5,307,459, US5,434,872, US5,732,094, US6,570,884, US6,115,776, and US6,327,625.
r8168  Copyright (C) 2011  Realtek NIC software team <nicfae@realtek.com>
 This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>.
 This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>.
r8168: egiga0: link down
ADDRCONF(NETDEV_UP): egiga0: link is not ready
*** Stage 2: Prepare the root file system ***
Mount system partition...
yaffs: dev is 32505864 name is "mtdblock8" ro
yaffs: passed flags ""
ls: /zyxel/mnt/nand/sysdisk.img.gz: No such file or directory
NAND Flash Corrupt...
Starting Pure-FTPd ...
/etc/init.d/rcS: line 178: /bin/pure-ftpd.official: not found
1 second...
2 second...
3 second...
4 second...
5 second...
6 second...
7 second...
8 second...
9 second...
10 second...


Please press Enter to activate this console.


BusyBox v1.17.2 (2013-03-27 16:11:13 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # ls
bin      etc      init     mnt      root     tmp      zyxel
dev      home     lib      proc     sbin     usr
e-data   i-data   linuxrc  ram_bin  sys      var

Mijzelf
Posts: 6198
Joined: Mon Jun 16, 2008 10:45 am

Re: failed update from 4.61 to 4.62 (NSA310)

Post by Mijzelf » Mon Nov 18, 2013 8:36 am

As far as I can see exact your problem was discussed (and solved) in this thread.

That there are 2 such problems in a very short time makes me wonder if there is a bug in 4.61, frustrating updates.

Post Reply