General NAS-Central Forums

Welcome to the NAS community
It is currently Tue Mar 28, 2017 11:33 pm

All times are UTC




Post new topic Reply to topic  [ 33 posts ]  Go to page Previous  1, 2, 3  Next
Author Message
PostPosted: Fri Nov 11, 2016 2:32 pm 
Offline

Joined: Fri Nov 11, 2016 2:19 pm
Posts: 6
Hi, I have installed Tvheadend on NAS326, but have problem with my USB TV Dongle, need kernel module af9033 for kernel 3.10.39, or kernel-headers for compile modules for my card. Can anyone help me?


Top
 Profile  
 
PostPosted: Fri Nov 11, 2016 5:46 pm 
Offline

Joined: Sun Apr 29, 2012 5:24 pm
Posts: 2210
Kernel as well as headers are not the problem. Most important is kernel config. Do you have it? What output gives you:
Code:
ls /proc/config* /boot/config*


Top
 Profile  
 
PostPosted: Fri Nov 11, 2016 9:19 pm 
Offline

Joined: Fri Nov 11, 2016 2:19 pm
Posts: 6
Unfortunately nothing, I am locked in stock firmware (v5.20). I have entware-ng installed, is there some way to install v4l drivers? On older NSA3x is v4l drivers via package from FFP, but it si for old kernel (2.6.x) I think, i need GPL sources of firmware for compiling, am i wrong? Sorry, I am newbie with this NAS ...


Top
 Profile  
 
PostPosted: Fri Nov 11, 2016 9:56 pm 
Offline

Joined: Sun Apr 29, 2012 5:24 pm
Posts: 2210
Having only config, you don't need GPL, unless kernel was too much patched and config would not be suitable for "raw" kernel.
Overall you are right. Having GPL source, it is easer. I saw here, that it should be available next Monday.


Top
 Profile  
 
PostPosted: Sat Nov 12, 2016 8:03 am 
Offline

Joined: Fri Nov 11, 2016 2:19 pm
Posts: 6
Thank you for your answer ... :) So i hope for GPL sources on Monday and then i try to compile drivers. I hate waiting for sources .... :D


Top
 Profile  
 
PostPosted: Sat Nov 12, 2016 6:34 pm 
Offline

Joined: Sun Apr 29, 2012 5:24 pm
Posts: 2210
You need to request a GPL copy at http://www.zyxel.com/us/en/form/gpl_oss_form.shtml I don't think, that it will be available for public download.


Top
 Profile  
 
PostPosted: Tue Nov 15, 2016 8:46 am 
Offline

Joined: Fri Nov 11, 2016 2:19 pm
Posts: 6
Yes I know, thank you. Right now I am downloading source code for NAS326 5.20 firmware.


Top
 Profile  
 
PostPosted: Tue Nov 15, 2016 9:08 am 
Offline

Joined: Fri Nov 11, 2016 2:19 pm
Posts: 6
Now i find it here on server too :)

http://gpl.nas-central.org/ZYXEL/NAS326_GPL/


Top
 Profile  
 
PostPosted: Tue Nov 15, 2016 2:20 pm 
Offline

Joined: Fri Nov 11, 2016 2:19 pm
Posts: 6
Ok, i found kernel config for NAS326, so i enable media support and select support for my TV card as kernel module. Than I compile kernel with modules and try load them on NAS326. Anything to care about that? Thank you .. :)


Top
 Profile  
 
PostPosted: Wed Nov 16, 2016 6:10 am 
Offline

Joined: Sun Apr 29, 2012 5:24 pm
Posts: 2210
rimmer wrote:
Anything to care about that? Thank you .. :)

Either it will load, either not.


Top
 Profile  
 
PostPosted: Sat Dec 31, 2016 1:15 pm 
Offline

Joined: Thu Sep 29, 2016 9:16 pm
Posts: 37
Hi Everyone!

My dvb device physically crashed so I ordered a new one:

http://www.ebay.com/itm/Hot-Sale-DVB-T- ... Sw8oFXz8QC

Bus 001 Device 004: ID 0bda:2838 Realtek Semiconductor Corp. RTL2838 DVB-T

But I can't see frontend in dvb directory:

/dev/dvb/adapter0:
total 0
drwxr-xr-x 2 root root 0 Dec 31 13:49 .
drwxr-xr-x 4 root root 0 Dec 31 13:49 ..
crw-rw---- 1 root video 212, 0 Dec 31 13:49 demux0
crw-rw---- 1 root video 212, 1 Dec 31 13:49 dvr0
crw-rw---- 1 root video 212, 2 Dec 31 13:49 net0

/dev/dvb/adapter1:
total 0
drwxr-xr-x 2 root root 0 Dec 31 13:49 .
drwxr-xr-x 4 root root 0 Dec 31 13:49 ..
crw-rw---- 1 root video 212, 3 Dec 31 13:49 demux0
crw-rw---- 1 root video 212, 4 Dec 31 13:49 dvr0
crw-rw---- 1 root video 212, 5 Dec 31 13:49 net0

dmesg says:

dvb-usb: no frontend was attached by 'RTL2832U DVB-T USB DEVICE'

Please help!

Thank you in advance!

Ikolo


Top
 Profile  
 
PostPosted: Sat Dec 31, 2016 5:00 pm 
Offline

Joined: Sun Apr 29, 2012 5:24 pm
Posts: 2210
As far as I remember mine v4l-dvb package has driver for your frontend-Rafael Micro R820T. Which NAS has you?
Some info needed. Please follow the steps strictly in a row.

1. Unplug DVB dongle.
2. Stop udev daemon service:
Code:
sh /ffp/start/udevd.sh stop
3. Run it in debug mode:
Code:
sh /ffp/start/udevd.sh debug
4. Attach dongle and let udev finish hotplug op. Copy output to pastebin.com and paste link here.
5. Stop debugging with key combination Ctrl+c.
6. Paste dmesg output here:
Code:
/bin/dmesg | tail -n20
7. Start udev daemon service again:
Code:
sh /ffp/start/udevd.sh start


Top
 Profile  
 
PostPosted: Sat Dec 31, 2016 6:29 pm 
Offline

Joined: Thu Sep 29, 2016 9:16 pm
Posts: 37
Hi!

Thank you the reply.

Certainly I use your dvb-usb-rtl2832u driver. (Earlier to my old dvb stick (1f4d:d803) too)

Patebin:

http://pastebin.com/P9KpHnBb

Dmesg:

/bin/dmesg | tail -n20
error try= 1!! write_rtl2832_stdi2c: ret=-32, DA=0xc0, len=2, data=(0xfb,0xd9,)
error try= 2!! write_rtl2832_stdi2c: ret=-32, DA=0xc0, len=2, data=(0xfb,0xd9,)
error try= 3!! write_rtl2832_stdi2c: ret=-32, DA=0xc0, len=2, data=(0xfb,0xd9,)
error try= 4!! write_rtl2832_stdi2c: ret=-32, DA=0xc0, len=2, data=(0xfb,0xd9,)
error try= 5!! write_rtl2832_stdi2c: ret=-32, DA=0xc0, len=2, data=(0xfb,0xd9,)
error try= 1!! read_rtl2832_stdi2c: ret=-32, DA=0xc0, len=1, data=(0xe0,)
error try= 2!! read_rtl2832_stdi2c: ret=-32, DA=0xc0, len=1, data=(0xe0,)
error try= 3!! read_rtl2832_stdi2c: ret=-32, DA=0xc0, len=1, data=(0xe0,)
error try= 4!! read_rtl2832_stdi2c: ret=-32, DA=0xc0, len=1, data=(0xe0,)
error try= 5!! read_rtl2832_stdi2c: ret=-32, DA=0xc0, len=1, data=(0xe0,)
error!! read_rtl2832_tuner_register: ret=-32, DA=0xc6, len=1, offset=0x0, data=(0x4c,)
error!! read_rtl2832_tuner_register: ret=-32, DA=0xc8, len=1, offset=0x2, data=(0x4c,)
error!! read_rtl2832_tuner_register: ret=-32, DA=0xc0, len=2, offset=0x0, data=(0x4c,0xbb,)
error!! read_rtl2832_tuner_register: ret=-32, DA=0xc6, len=1, offset=0x0, data=(0x4c,)
-check_tuner_type : Unknown tuner on board...
dvb-usb: no frontend was attached by 'RTL2832U DVB-T USB DEVICE'
input: IR-receiver inside an USB DVB receiver as /devices/platform/ehci_marvell.70059/usb1/1-1/1-1.3/input/input3
dvb-usb: schedule remote query interval to 287 msecs.
dvb-usb: RTL2832U DVB-T USB DEVICE successfully initialized and connected.
+rc_frt2

I don't know what's the problem. Wrong stick or it is not Rafael Micro R820T?

Ikolo


Top
 Profile  
 
PostPosted: Sat Dec 31, 2016 11:34 pm 
Offline

Joined: Sun Apr 29, 2012 5:24 pm
Posts: 2210
Ikolo wrote:
Certainly I use your dvb-usb-rtl2832u driver.

Certainly your tuner is Rafael Micro R820T. You are using old driver, which you downloaded and installed manually. I can see that from your given outputs, because current RTL2832U driver from latest v4l-dvb package has no ending 'u' and it doesn't emitting driver debug output to dmesg buffer. Current driver name is dvb-usb-rtl2832 and it is placed in:
Quote:
/ffp/lib/modules/2.6.31.8/updates/usb/dvb-usb/dvb-usb-rtl2832.ko
This driver supports tuner Rafael Micro R820T, which is located at:
Quote:
/ffp/lib/modules/2.6.31.8/updates/tuners/r820t.ko
, while your manually installed dvb-usb-rtl2832u doesn't.

You should remove that old driver first. Only after that, follow these instructions step by step:
1. Make sure that you doesn't have module_utils package installed. If yes, remove it:
Code:
slacker -r module_utils

2. If you had module_utils installed, then reinstall kmod package (if not then skip this step)
Code:
slacker -UAa br2:kmod

3. Install latest v4l-dvb package:
Code:
slacker -UAa br2:v4l-dvb

4. Just in case restart udev daemon service:
Code:
sh /ffp/start/udevd.sh restart

5. Plug your dvb dongle.

6. Check dmesg output:
Code:
/bin/dmesg | tail -n20


Top
 Profile  
 
PostPosted: Sun Jan 01, 2017 12:43 am 
Offline

Joined: Thu Sep 29, 2016 9:16 pm
Posts: 37
Hi!

Happy New Year!

I thought I need this driver:
http://downloads.zyxel.nas-central.org/ ... tl2832u.ko
(I used this my older device.)
Sorry!

Dmesg:

/bin/dmesg | tail -n20
Adding 524280k swap on /i-data/.system/swap_ul6545p. Priority:-1 extents:4 across:542712k
svc: failed to register lockdv1 RPC service (errno 97).
GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1

usb 1-1.3: new high speed USB device using ehci_marvell and address 4
In hub_port_init, and number is 2, retry 0, port 3 .....
usb 1-1.3: configuration #1 chosen from 1 choice
In usb_disconnect, and number is 1 .....
usb 1-1.3: USB disconnect, address 4
usb 1-1.3: new high speed USB device using ehci_marvell and address 5
In hub_port_init, and number is 2, retry 0, port 3 .....
usb 1-1.3: configuration #1 chosen from 1 choice
dvb-usb: found a 'RTL2832U DVB-T USB DEVICE' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (RTL2832U DVB-T USB DEVICE)
usb 1-1.3: DVB: registering adapter 0 frontend 0 (Realtek DVB-T RTL2832)...
input: IR-receiver inside an USB DVB receiver as /devices/platform/ehci_marvell.70059/usb1/1-1/1-1.3/input/input0
dvb-usb: schedule remote query interval to 287 msecs.
dvb-usb: RTL2832U DVB-T USB DEVICE successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_rtl2832u

Thanks!!!!

Now, I just see one adapter. Is it possible?

Ikolo


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 33 posts ]  Go to page Previous  1, 2, 3  Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 31 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group