General NAS-Central Forums

Welcome to the NAS community
It is currently Sun Feb 25, 2018 2:09 am

All times are UTC




Post new topic Reply to topic  [ 281 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6, 7 ... 19  Next
Author Message
PostPosted: Fri Feb 17, 2012 12:31 pm 
Offline

Joined: Wed Feb 08, 2012 6:33 pm
Posts: 6
Patch v5.1 with new arcNumbers (nsa320 = 3956, nsa310 = 4022):
http://pastebin.com/3LNtYZSD


Top
 Profile  
 
PostPosted: Tue Feb 21, 2012 1:05 am 
Offline

Joined: Sun Nov 13, 2011 3:31 pm
Posts: 26
@peeter123: According to your comment here this error seems to be raid/partition table related. My kernel has raid enabled, but not used

on old install - just installed on sda2, mtdblock7 errors occurs
Quote:
mdadm: sending ioctl 800c0910 to a partition!
uncorrectable error :
end_request: I/O error, dev mtdblock7, sector 0

on fresh install - partition sda2 has been deleted during install, installer was restarted and sda2 has been created and formatted - no errors

I'm installing on another box to confirm - again, no error


Top
 Profile  
 
PostPosted: Sat Feb 25, 2012 6:57 am 
Offline

Joined: Wed Jan 11, 2012 11:35 pm
Posts: 34
If some kind person could decipher the problem below I would be extremenly grateful -
I have installed Debian twice now but receive the same error when testing the install that it can't find the root partition.

Details -
Followed Peter's guide apart from the partitioning where I let the debian installer automatically partition for 'a separate /home' , see -

#1 1.0 MB K biosgrub
#2 10.0 GB B f ext3 /
#3 510.0 MB f swap swap
#4 2.0 TB f ext3 /home
8.2 kB FREE SPACE
SCSI3 (0,0,0) (sdb) - 1.0 GB Kingston DataTraveler 2.0
#1 primary 995.2 MB fat32

(The Kingston USB stick is my installation media)

As the installation was finishing, the console displayed this message -

No boot loader installed
No boot loader has been installed, either because you chose not to or
because your specific architecture doesn't support a boot loader yet.

You will need to boot manually with the kernel on partition
/dev/sda2 and root=/dev/sda2 passed as a kernel argument.

<Continue>


I let the installer complete and attempt to reboot the system, and I interrupted the boot.
Following Peter's guide I attempted to test my install, substituting SDA2 for SDA1 but received an error that it can't find the partition -

setenv bootargs 'console=ttyS0,115200 root=/dev/sda2'

bootm 0x800000

=====<CUT>=======

VFS: Cannot open root device "sda2" or unknown-block(8,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00 1024 mtdblock0 (driver?)
1f01 512 mtdblock1 (driver?)
1f02 512 mtdblock2 (driver?)
1f03 512 mtdblock3 (driver?)
1f04 10240 mtdblock4 (driver?)
1f05 10240 mtdblock5 (driver?)
1f06 48896 mtdblock6 (driver?)
1f07 10240 mtdblock7 (driver?)
1f08 48896 mtdblock8 (driver?)
0800 1953514584 sda driver: sd
0801 1953514583 sda1 00000000-0000-0000-0000-000000000sda1
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,2)
USB power enabled

On my previous attempt I partitioned the disks differently, but received a similar error.
I then tried to recover the system but could not mount the disks so I hoped the re-install last night would have worked.

Can anyone please help?
Thanks
Mark


Top
 Profile  
 
PostPosted: Sat Feb 25, 2012 8:43 am 
Offline

Joined: Wed Jan 11, 2012 11:35 pm
Posts: 34
I also tried SDA1 (just in case it was that easy!)

No filesystem could mount root, tried: reiserfs ext3 ext2 ext4 vfat msdos iso96
60 ntfs udf
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
USB power enabled


Top
 Profile  
 
PostPosted: Sat Feb 25, 2012 1:54 pm 
Offline

Joined: Sat Feb 25, 2012 1:48 pm
Posts: 2
Add rootdelay=3 (or more, inseconds) to bootargs

setenv bootargs 'console=ttyS0,115200 root=/dev/sda2 rootdelay=3'

This will allow the detection of the disk by the kernel.


Top
 Profile  
 
PostPosted: Sat Feb 25, 2012 2:06 pm 
Offline

Joined: Sat Feb 25, 2012 1:48 pm
Posts: 2
Piotr, can you add support for USB LED (rd / wr) to your patch

Here my finished code based on your code:
file nsa3x0-setup.c:

{
.name = "nsa320:green:USB",
.default_trigger = "usbr-disk",
.gpio = 15,
.active_low = 0,
},
{
.name = "nsa320:red:USB",
.default_trigger = "usbw-disk",
.gpio = 16,
.active_low = 0,
},

new file /drivers/leds/ledtrig-usb-disk.c
/*
* LED USB-Disk Activity Trigger
*
* Author: Slawomir Gajzner
*
* Based on "LED IDE-Disk Activity Trigger"
* by Richard Purdie <rpurdie@openedhand.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/

#include <linux/module.h>
#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/timer.h>
#include <linux/leds.h>


DEFINE_LED_TRIGGER(ledtrig_usb_rd);
DEFINE_LED_TRIGGER(ledtrig_usb_wr);

static void ledtrig_usb_timerfunc(unsigned long data);
static DEFINE_TIMER(ledtrig_usb_timer, ledtrig_usb_timerfunc, 0, 0);

static int usb_activity=0;
static int usb_lastactivity=0;
static unsigned char usb_rd=0, usb_wr=0;


void ledtrig_usb_activity(int wr)
{
if(wr) usb_wr = 1;
else usb_rd = 1;

usb_activity++;
if (!timer_pending(&ledtrig_usb_timer))
mod_timer(&ledtrig_usb_timer, jiffies + msecs_to_jiffies(10));
}
EXPORT_SYMBOL(ledtrig_usb_activity);

static void ledtrig_usb_timerfunc(unsigned long data)
{
if (usb_lastactivity != usb_activity) {
usb_lastactivity = usb_activity;

if(usb_rd){
usb_rd = 0;
led_trigger_event(ledtrig_usb_rd, INT_MAX);
}
else led_trigger_event(ledtrig_usb_rd, LED_OFF);
if(usb_wr){
usb_wr = 0;
led_trigger_event(ledtrig_usb_wr, INT_MAX);
}
else led_trigger_event(ledtrig_usb_wr, LED_OFF);

mod_timer(&ledtrig_usb_timer, jiffies + msecs_to_jiffies(10));
} else {
led_trigger_event(ledtrig_usb_rd, LED_OFF);
led_trigger_event(ledtrig_usb_wr, LED_OFF);
}
}

static int __init ledtrig_usb_init(void)
{
led_trigger_register_simple("usbr-disk", &ledtrig_usb_rd);
led_trigger_register_simple("usbw-disk", &ledtrig_usb_wr);
return 0;
}

static void __exit ledtrig_usb_exit(void)
{
led_trigger_unregister_simple(ledtrig_usb_rd);
led_trigger_unregister_simple(ledtrig_usb_wr);
}

module_init(ledtrig_usb_init);
module_exit(ledtrig_usb_exit);

MODULE_AUTHOR("Slawomir Gajzner");
MODULE_DESCRIPTION("LED USB Disk Activity Trigger");
MODULE_LICENSE("GPL");


Modify line in /drivers/leds/Makefile
obj-$(CONFIG_LEDS_TRIGGER_SATA_DISK) += ledtrig-sata-disk.o ledtrig-usb-disk.o

Modify /drivers/usb/storage/transport.c
+#include <linux/leds.h>

in function usb_stor_invoke_transport (above srb->result = SAM_STAT_GOOD; )
+ if (srb->cmnd[0] == READ_10) ledtrig_usb_activity(0);
+ if (srb->cmnd[0] == WRITE_10) ledtrig_usb_activity(1);


In file /include/leds.h
#ifdef CONFIG_LEDS_TRIGGER_SATA_DISK
extern void ledtrig_sata_activity(int port, int wr);
+extern void ledtrig_usb_activity(int wr);
#else
#define ledtrig_sata_activity() do {} while(0)
+#define ledtrig_usb_activity() do {} while(0)
#endif


Testet in kernel 3.2.1


Top
 Profile  
 
PostPosted: Sat Feb 25, 2012 7:58 pm 
Offline

Joined: Wed Jan 11, 2012 11:35 pm
Posts: 34
Slawek, thanks for the advice 'rootdelay=3', unfortunately it didn't make any difference even when set to 10.
I'm wondering if it's the geometry of my 2TB disk or the fact that the /home partition is 2tb.
Sda2 is obviously created for the install but the kernel can't see it when I try to load it later.

I have spent many hours on this now, days in fact :shock:
Any other suggestions before I give up :(

Thanks - Mark


Top
 Profile  
 
PostPosted: Sat Feb 25, 2012 10:12 pm 
Offline

Joined: Sun Dec 04, 2011 12:38 am
Posts: 37
Location: Enschede, the Netherlands
scoobie, that's a weird problem indeed. Try to structure your partitions like this:

/ primary
----Extended----
|/home|
|swap|

And try to redownload uImage-3.2. I've made some changes ;)


Top
 Profile  
 
PostPosted: Sat Feb 25, 2012 10:48 pm 
Offline

Joined: Wed Feb 08, 2012 6:33 pm
Posts: 6
Patch v5.2 with USB read/write LEDs:
http://pastebin.com/LkF8Q1dH

For NSA320 disable "CONFIG_MACH_NSA310".

slawek wrote:
nsa320:red:USB

NSA320 don't have two color USB LED.


Top
 Profile  
 
PostPosted: Sun Feb 26, 2012 9:45 am 
Offline

Joined: Wed Jan 11, 2012 11:35 pm
Posts: 34
Peeter - downloaded your new kernel but it now hangs on the initial boot.
Strange - please see below -

setenv mainlineLinux yes

NSA310>> setenv arcNumber 3339

NSA310>> saveenv

Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
NSA310>> reset

þ
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Jun 8 2011 - 18:48:37) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0, egiga1 [PRIME]
Hit any key to stop autoboot: 2  0
NSA310>> usb start

(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
NSA310>> fatload usb 0 0x800000 uImage-3.2

reading uImage-3.2
..................................................................................................................................................................................................................................................

2479704 bytes read
NSA310>> fatload usb 0 0xb00000 initrd.gz

reading initrd.gz
.........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

9437184 bytes read
NSA310>> setenv bootargs 'console=ttyS0,115200 root=/dev/ram initrd=0xb00000,0x900000 ramdisk=32768'

NSA310>> bootm 0x800000

## Booting image at 00800000 ...
Image Name: Linux-3.2.0
Created: 2012-02-18 17:01:42 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2479640 Bytes = 2.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 3.2.0 (peter@Ubuntu) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) ) #9 Sat Feb 18 18:01:39 CET 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Zyxel NSA-310
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 root=/dev/ram initrd=0xb00000,0x900000 ramdisk=32768
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 245624k/245624k available, 16520k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0477000 (4540 kB)
.init : 0xc0477000 - 0xc049f000 ( 160 kB)
.data : 0xc04a0000 - 0xc04c7ae0 ( 159 kB)
.bss : 0xc04c7b04 - 0xc04e6fd4 ( 126 kB)
NR_IRQS:114
sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
Power resume enabled
Power-off GPIO enabled
Kirkwood PCIe port 0:
link up
PCI: bus0 uses PCIe port 0
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref]
pci 0000:00:01.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref]
pci 0000:00:01.0: BAR 4: set to [mem 0xe0010000-0xe0013fff 64bit pref] (PCI address [0xe0010000-0xe0013fff])
pci 0000:00:01.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref]
pci 0000:00:01.0: BAR 2: set to [mem 0xe0014000-0xe0014fff 64bit pref] (PCI address [0xe0014000-0xe0014fff])
pci 0000:00:01.0: BAR 0: assigned [io 0x1000-0x10ff]
pci 0000:00:01.0: BAR 0: set to [io 0x1000-0x10ff] (PCI address [0x1000-0x10ff])
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.24.
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 9216K
NetWinder Floating Point Emulator V0.97 (double precision)
NTFS driver 2.1.30 [Flags: R/W].
msgmni has been set to 497
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler cfq registered (default)
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 21
ata2: SATA max UDMA/133 irq 21
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 5 at 0x0000000a0000
Bad eraseblock 666 at 0x000005340000
Bad eraseblock 871 at 0x000006ce0000
modprobe: FATAL: Could not load /lib/modules/3.2.0/modules.dep: No such file or directory


Creating 9 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:00:01.0: eth0: RTL8168d/8111d at 0xd0806000, 00:00:00:00:00:30, XID 083000c0 IRQ 9
r8169 0000:00:01.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Orion Watchdog Timer: Initial timeout 21 sec
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
cpuidle: using governor ladder
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
modprobe: FATAL: Could not load /lib/modules/3.2.0/modules.dep: No such file or directory


usbcore: registered new interface driver snd-usb-audio
ALSA device list:
No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3981 buckets, 15924 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Registering the dns_resolver key type
input: gpio-keys as /devices/platform/gpio-keys/input/input0
rtc-mv rtc-mv: setting system clock to 2012-02-26 09:40:04 UTC (1330249204)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
usb 1-1: new high-speed USB device number 2 using orion-ehci
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.2: new high-speed USB device number 3 using orion-ehci
ata1.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
scsi2 : usb-storage 1-1.2:1.0
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link down (SStatus 0 SControl F300)
Freeing init memory: 160K
mount: mounting tmpfs on /dev failed: Invalid argument
Kernel panic - not syncing: Attempted to kill init!


Top
 Profile  
 
PostPosted: Sun Feb 26, 2012 10:17 am 
Offline

Joined: Wed Jan 11, 2012 11:35 pm
Posts: 34
Peter, I have booted off your original 3.2 kernel and the installer boots again - good, I thought I may have toasted my NSA!
One thing that I can't work out is how to create a logical disk. The Debain installation manual says that you should be presented with the option, but all I see is size and 'beginning or end' then there is no option to change it.
Anyway I have now partitioned as follows, so fingers crossed.
Thanks for your help - it's appreciated 8-)

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ [!!] Partition disks ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ ³
³ This is an overview of your currently configured partitions and mount ³
³ points. Select a partition to modify its settings (file system, mount ³
³ point, etc.), a free space to create partitions, or a device to ³
³ initialize its partition table. ³
³ ³
³ Guided partitioning ³
³ Configure software RAID ± ³
³ Configure encrypted volumes ± ³
³ ± ³
³ SCSI1 (0,0,0) (sda) - 2.0 TB ATA WDC WD20EARX-00P ± ³
³ > #1 5.0 GB f ext4 / ³
³ > #2 1.8 TB f ext4 /home ± ³
³ > #3 500.0 MB f swap swap ± ³
³ > 194.9 GB FREE SPACE ± ³
³ SCSI3 (0,0,0) (sdb) - 1.0 GB Kingston DataTraveler 2.0 ³
³ ³
³ <Go Back>


Top
 Profile  
 
PostPosted: Sun Feb 26, 2012 11:52 am 
Offline

Joined: Wed Jan 11, 2012 11:35 pm
Posts: 34
Aaargh! :cry:

Re-installed using original 3.2 kernel and partitions as previously described and same old error. Tried with rootdelay=5 still fails -


(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
NSA310>> fatload usb 0 0x800000 uImage32

reading uImage32
...............................................................................................................................................................................................................................................

2452744 bytes read
NSA310>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=5'

NSA310>> bootm 0x800000

## Booting image at 00800000 ...
Image Name: Linux-3.2.0
Created: 2012-01-07 15:43:57 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2452680 Bytes = 2.3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 3.2.0 (peter@Ubuntu) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) ) #6 Sat Jan 7 16:43:55 CET 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Zyxel NSA-310
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=5
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 254904k/254904k available, 7240k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0467000 (4476 kB)
.init : 0xc0467000 - 0xc048f000 ( 160 kB)
.data : 0xc0490000 - 0xc04b7540 ( 158 kB)
.bss : 0xc04b7564 - 0xc04d6a34 ( 126 kB)
NR_IRQS:114
sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
Power resume enabled
Power-off GPIO enabled
Kirkwood PCIe port 0:
link up
PCI: bus0 uses PCIe port 0
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref]
pci 0000:00:01.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref]
pci 0000:00:01.0: BAR 4: set to [mem 0xe0010000-0xe0013fff 64bit pref] (PCI address [0xe0010000-0xe0013fff])
pci 0000:00:01.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref]
pci 0000:00:01.0: BAR 2: set to [mem 0xe0014000-0xe0014fff 64bit pref] (PCI address [0xe0014000-0xe0014fff])
pci 0000:00:01.0: BAR 0: assigned [io 0x1000-0x10ff]
pci 0000:00:01.0: BAR 0: set to [io 0x1000-0x10ff] (PCI address [0x1000-0x10ff])
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.24.
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
NTFS driver 2.1.30 [Flags: R/W].
msgmni has been set to 497
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler cfq registered (default)
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 21
ata2: SATA max UDMA/133 irq 21
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 0 at 0x000000000000
Bad eraseblock 1 at 0x000000020000
=======<CUT>========<CUT>============
Bad eraseblock 1020 at 0x000007f80000
Bad eraseblock 1021 at 0x000007fa0000
Bad eraseblock 1022 at 0x000007fc0000
Bad eraseblock 1023 at 0x000007fe0000
sched: RT throttling activated
Creating 9 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address c8:6c:87:0a:ef:7e
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:00:01.0: eth1: RTL8168d/8111d at 0xd0806000, 00:00:00:00:00:30, XID 083000c0 IRQ 9
r8169 0000:00:01.0: eth1: jumbo features [frames: 9200 bytes, tx checksumming: ko]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
rtc-pcf8563 0-0051: chip found, driver version 0.4.3
rtc-pcf8563 0-0051: pcf8563_get_datetime: read error
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc1
Orion Watchdog Timer: Initial timeout 21 sec
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
ALSA device list:
No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3982 buckets, 15928 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Registering the dns_resolver key type
input: gpio-keys as /devices/platform/gpio-keys/input/input0
rtc-mv rtc-mv: setting system clock to 2012-02-26 11:40:35 UTC (1330256435)
Waiting 5sec before mounting root device...
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
usb 1-1: new high-speed USB device number 2 using orion-ehci
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
ata1.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
usb 1-1.2: new high-speed USB device number 3 using orion-ehci
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
scsi2 : usb-storage 1-1.2:1.0
ata2: SATA link down (SStatus 0 SControl F300)
scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: [sdb] 1953792 512-byte logical blocks: (1.00 GB/954 MiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] No Caching mode page present
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] No Caching mode page present
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] No Caching mode page present
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Attached SCSI removable disk
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
grow_buffers: requested out-of-range block 18446744073321613486 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907029166, location=-387938130
grow_buffers: requested out-of-range block 18446744073321613230 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907028910, location=-387938386
grow_buffers: requested out-of-range block 18446744073321613485 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907029165, location=-387938131
grow_buffers: requested out-of-range block 18446744073321613229 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907028909, location=-387938387
grow_buffers: requested out-of-range block 18446744073321613484 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907029164, location=-387938132
grow_buffers: requested out-of-range block 18446744073321613228 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907028908, location=-387938388
grow_buffers: requested out-of-range block 18446744073321613336 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907029016, location=-387938280
grow_buffers: requested out-of-range block 18446744073321613080 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907028760, location=-387938536
grow_buffers: requested out-of-range block 18446744073321613334 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907029014, location=-387938282
grow_buffers: requested out-of-range block 18446744073321613078 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3907028758, location=-387938538
grow_buffers: requested out-of-range block 18446744072382089390 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767521, location=-1089199775
grow_buffers: requested out-of-range block 18446744072382089078 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767265, location=-1089200031
grow_buffers: requested out-of-range block 18446744072382089389 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767520, location=-1089199776
grow_buffers: requested out-of-range block 18446744072382089077 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767264, location=-1089200032
grow_buffers: requested out-of-range block 18446744072382089079 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767266, location=-1089200030
grow_buffers: requested out-of-range block 18446744072382089381 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767519, location=-1089199777
grow_buffers: requested out-of-range block 18446744072382089069 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767263, location=-1089200033
grow_buffers: requested out-of-range block 18446744072382089205 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767371, location=-1089199925
grow_buffers: requested out-of-range block 18446744072382088893 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767115, location=-1089200181
grow_buffers: requested out-of-range block 18446744072382089203 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767369, location=-1089199927
grow_buffers: requested out-of-range block 18446744072382088891 for device sda1
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=3205767113, location=-1089200183
UDF-fs: warning (device sda1): udf_fill_super: No partition found (1)
List of all partitions:
1f00 1024 mtdblock0 (driver?)
1f01 512 mtdblock1 (driver?)
1f02 512 mtdblock2 (driver?)
1f03 512 mtdblock3 (driver?)
1f04 10240 mtdblock4 (driver?)
1f05 10240 mtdblock5 (driver?)
1f06 48896 mtdblock6 (driver?)
1f07 10240 mtdblock7 (driver?)
1f08 48896 mtdblock8 (driver?)
0800 1953514584 sda driver: sd
0801 1953514583 sda1 00000000-0000-0000-0000-000000000sda1
0810 976896 sdb driver: sd
0811 971901 sdb1 00000000-0000-0000-0000-000000000sdb1
No filesystem could mount root, tried: reiserfs ext3 ext2 ext4 vfat msdos iso9660 ntfs udf
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
USB power enabled


Top
 Profile  
 
PostPosted: Sun Feb 26, 2012 11:53 am 
Offline

Joined: Wed Jan 11, 2012 11:35 pm
Posts: 34
Tried the install with the new 3.2 kernel and slightly different boot messages -

NSA310>> fatload usb 0 0x800000 uImage-3.2
reading uImage-3.2
................................................................................
................................................................................
................................................................................
..

2479704 bytes read
NSA310>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=5'
NSA310>> bootm 0x800000
## Booting image at 00800000 ...
Image Name: Linux-3.2.0
Created: 2012-02-18 17:01:42 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2479640 Bytes = 2.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 3.2.0 (peter@Ubuntu) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubun
tu3) ) #9 Sat Feb 18 18:01:39 CET 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Zyxel NSA-310
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=5
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 254840k/254840k available, 7304k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0477000 (4540 kB)
.init : 0xc0477000 - 0xc049f000 ( 160 kB)
.data : 0xc04a0000 - 0xc04c7ae0 ( 159 kB)
.bss : 0xc04c7b04 - 0xc04e6fd4 ( 126 kB)
NR_IRQS:114
sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
Power resume enabled
Power-off GPIO enabled
Kirkwood PCIe port 0:
link up
PCI: bus0 uses PCIe port 0
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref]
pci 0000:00:01.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref]
pci 0000:00:01.0: BAR 4: set to [mem 0xe0010000-0xe0013fff 64bit pref] (PCI addr
ess [0xe0010000-0xe0013fff])
pci 0000:00:01.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref]
pci 0000:00:01.0: BAR 2: set to [mem 0xe0014000-0xe0014fff 64bit pref] (PCI addr
ess [0xe0014000-0xe0014fff])
pci 0000:00:01.0: BAR 0: assigned [io 0x1000-0x10ff]
pci 0000:00:01.0: BAR 0: set to [io 0x1000-0x10ff] (PCI address [0x1000-0x10ff]
)
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.24.
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
NTFS driver 2.1.30 [Flags: R/W].
msgmni has been set to 497
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler cfq registered (default)
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 21
ata2: SATA max UDMA/133 irq 21
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bi
t)
Scanning device for bad blocks
Bad eraseblock 5 at 0x0000000a0000
Bad eraseblock 666 at 0x000005340000
Bad eraseblock 871 at 0x000006ce0000
Creating 9 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:00:01.0: eth0: RTL8168d/8111d at 0xd0806000, 00:00:00:00:00:30, XID 0
83000c0 IRQ 9
r8169 0000:00:01.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: k
o]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Orion Watchdog Timer: Initial timeout 21 sec
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
cpuidle: using governor ladder
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
ALSA device list:
No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3981 buckets, 15924 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Registering the dns_resolver key type
input: gpio-keys as /devices/platform/gpio-keys/input/input0
rtc-mv rtc-mv: setting system clock to 2012-02-26 11:42:46 UTC (1330256566)
Waiting 5sec before mounting root device...
usb 1-1: new high-speed USB device number 2 using orion-ehci
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.2: new high-speed USB device number 3 using orion-ehci
ata1.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
scsi2 : usb-storage 1-1.2:1.0
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link down (SStatus 0 SControl F300)
scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: [sdb] 1953792 512-byte logical blocks: (1.00 GB/954 MiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] No Caching mode page present
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] No Caching mode page present
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] No Caching mode page present
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Attached SCSI removable disk
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
List of all partitions:
1f00 1024 mtdblock0 (driver?)
1f01 512 mtdblock1 (driver?)
1f02 512 mtdblock2 (driver?)
1f03 512 mtdblock3 (driver?)
1f04 10240 mtdblock4 (driver?)
1f05 10240 mtdblock5 (driver?)
1f06 48896 mtdblock6 (driver?)
1f07 10240 mtdblock7 (driver?)
1f08 48896 mtdblock8 (driver?)
0800 1953514584 sda driver: sd
0801 1953514583 sda1 00000000-0000-0000-0000-000000000sda1
0810 976896 sdb driver: sd
0811 971901 sdb1 00000000-0000-0000-0000-000000000sdb1
No filesystem could mount root, tried: reiserfs ext3 ext2 ext4 vfat msdos ntfs
Kernel panic - not syncing: VFS: Una
ble to mount root fs on unknown-block(8,1)
USB power enabled


Top
 Profile  
 
PostPosted: Sun Feb 26, 2012 1:42 pm 
Offline

Joined: Sun Dec 04, 2011 12:38 am
Posts: 37
Location: Enschede, the Netherlands
I've had similar problems when using initrd, but you are not using that. This is my bootlog with the same kernel:

Code:
......
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
ata1.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
 sda: sda1 sda2 < sda5 sda6 > sda3
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-1.3: new full-speed USB device number 3 using orion-ehci
ata2: SATA link down (SStatus 0 SControl F300)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
EXT3-fs (sda1): error: couldn't mount because of unsupported optional features (240)
EXT2-fs (sda1): error: couldn't mount because of unsupported optional features (240)
hub 1-1.3:1.0: USB hub found
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 8:1.
hub 1-1.3:1.0: 4 ports detected
devtmpfs: mounted
Freeing init memory: 160K
usb 1-1.3.3: new full-speed USB device number 4 using orion-ehci
input: USB Headphone Set as /devices/platform/orion-ehci.0/usb1/1-1/1-1.3/1-1.3.3/1-1.3.3:1.3/input/input1
generic-usb 0003:0C76:1607.0001: input: USB HID v1.00 Device [USB Headphone Set] on usb-orion-ehci.0-1.3.3/input3
udevd[569]: starting version 175
udevd[589]: renamed network interface eth0 to eth1
Adding 495612k swap on /dev/sda5.  Priority:-1 extents:1 across:495612k
EXT4-fs (sda1): re-mounted. Opts: (null)
EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
......


Top
 Profile  
 
PostPosted: Sun Feb 26, 2012 1:44 pm 
Offline

Joined: Wed Jan 11, 2012 11:35 pm
Posts: 34
Tried to force the root partition fstype (just in case) -

setenv bootargs 'console=ttyS0,115200 rootfstype=ext4 root=/dev/sda1 rootdelay=10'

Still broke ...

List of all partitions:
1f00 1024 mtdblock0 (driver?)
1f01 512 mtdblock1 (driver?)
1f02 512 mtdblock2 (driver?)
1f03 512 mtdblock3 (driver?)
1f04 10240 mtdblock4 (driver?)
1f05 10240 mtdblock5 (driver?)
1f06 48896 mtdblock6 (driver?)
1f07 10240 mtdblock7 (driver?)
1f08 48896 mtdblock8 (driver?)
0800 1953514584 sda driver: sd
0801 1953514583 sda1 00000000-0000-0000-0000-000000000sda1
0810 976896 sdb driver: sd
0811 971901 sdb1 00000000-0000-0000-0000-000000000sdb1
No filesystem could mount root, tried: ext4
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
USB power enabled


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 281 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6, 7 ... 19  Next

All times are UTC


Who is online

Users browsing this forum: billbillw and 77 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group