General NAS-Central Forums

Welcome to the NAS community
It is currently Sun Apr 30, 2017 1:12 am

All times are UTC




Post new topic Reply to topic  [ 70 posts ]  Go to page Previous  1, 2, 3, 4, 5
Author Message
PostPosted: Wed Jun 25, 2014 8:00 pm 
Offline

Joined: Fri Mar 14, 2014 9:46 pm
Posts: 32
@Mijzelf

My NAS is not fried !!! :D :D

I'll finally to recover it , good luck to me :D


Top
 Profile  
 
PostPosted: Sat Nov 08, 2014 10:31 am 
Offline

Joined: Sat Nov 08, 2014 10:09 am
Posts: 4
i wrongly flashed my IX4-200d with cloud edition firmware, now i have boot loop with iomega logo.
I can't reach usb boot. can anyone help me to flash original firmware?


Top
 Profile  
 
PostPosted: Sun Nov 09, 2014 2:14 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5981
Did you read the thread?


Top
 Profile  
 
PostPosted: Sun Nov 09, 2014 5:59 pm 
Offline

Joined: Sat Nov 08, 2014 10:09 am
Posts: 4
Mijzelf wrote:
Did you read the thread?

i read the thread, but i can't understand well:D...
i haven't pinout on my board i have 10 soldered holes.
i have a pc with serial port can i connect with a serial cable where i sodered a wire on pin 2 -3 and 5? or can i use a usb to serial converter?


Top
 Profile  
 
PostPosted: Sun Nov 09, 2014 6:50 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5981
You can't use a 'normal' serial port, you need a TTL signal. Something like this. And yes, then you can solder a wire on the mobo. GND, TX en RX are needed.


Top
 Profile  
 
PostPosted: Tue Nov 11, 2014 7:28 pm 
Offline

Joined: Sat Nov 08, 2014 10:09 am
Posts: 4
i'm waiting for ttl converter. thanks for reply! can i use putty to connect?


Top
 Profile  
 
PostPosted: Wed Nov 12, 2014 8:35 am 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5981
Yes.


Top
 Profile  
 
PostPosted: Tue Dec 09, 2014 8:19 pm 
Offline

Joined: Sun Sep 28, 2014 7:28 am
Posts: 1
I too have the same issues, a bricked iomega.
I have read this topic, and have bought a TTI Serial cable;
But I am confused to which pins I need to attach.

On my cable I have 6 cables on my TTI serial cable :

- White
- Green
- Yellow
- Orange
- Blue
- Black

Can someone tell me on which pin I need to connect which cable?
Greatly appreciated.


Top
 Profile  
 
PostPosted: Sun Dec 14, 2014 6:26 pm 
Offline

Joined: Sat Nov 08, 2014 10:09 am
Posts: 4
i received my ttl converter i connected it to right pin, but when i try to connect with putty i've only a black screen no text...???? :shock: :shock:


Top
 Profile  
 
PostPosted: Thu May 28, 2015 12:23 am 
Offline

Joined: Wed May 27, 2015 12:43 pm
Posts: 6
Hi All

I have a ix4-200d cloud edition and the bios update from usb failed. I too have repeated reboots . I have read the forum and have been successfully able to console into the machine. Ive followed everybody's commands for tftpboot, etc. everytime I get the bad magic error after about 5%. ive tried the files from ix4-200d-3.2.6.17887-recovery

I know this is an old thread but any assistance would be greatly appreciated. ive spend hours surfing the web and I don't think there is much of anything that I haven't tried that ive found so far

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.1 **

** MARVELL BOARD: IX4-110 LE

U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Found 0x20 i2c device
Set Power State as Always On
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
Found ADT7473, program LED ...(led_volt=90) OK
Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK

Marvell Serial ATA Adapter
Integrated Sata device found


CPU : Marvell Feroceon (Rev 1)
Found initrd at 0x2d8000

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is RGMII

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
flags: 64bit ncq stag led pmp slum part
scanning bus for devices...
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0xb0000, size 0x228000

Reading data from 0x2d7e00 -- 100% complete.
2260992 bytes read: OK

NAND read: device 0 offset 0x2d8000, size 0x2f0000

Reading data from 0x2fd800 -- 5% complete.reading NAND page at offset 0x304000 failed
3080192 bytes read: ERROR
## Booting image at 02000000 ...
Image Name: Linux-2.6.31.8
Created: 2012-02-13 21:48:28 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2077080 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 12000000 ...
Bad Magic Number▒


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 70 posts ]  Go to page Previous  1, 2, 3, 4, 5

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group