IX4-200d rebooting constantly

Qesc
Posts: 32
Joined: Fri Mar 14, 2014 9:46 pm

Re: IX4-200d rebooting constantly

Post by Qesc » Wed Jun 25, 2014 8:00 pm

@Mijzelf

My NAS is not fried !!! :D :D

I'll finally to recover it , good luck to me :D

vascolizzato
Posts: 4
Joined: Sat Nov 08, 2014 10:09 am

Re: IX4-200d rebooting constantly

Post by vascolizzato » Sat Nov 08, 2014 10:31 am

i wrongly flashed my IX4-200d with cloud edition firmware, now i have boot loop with iomega logo.
I can't reach usb boot. can anyone help me to flash original firmware?

Mijzelf
Posts: 6194
Joined: Mon Jun 16, 2008 10:45 am

Re: IX4-200d rebooting constantly

Post by Mijzelf » Sun Nov 09, 2014 2:14 pm

Did you read the thread?

vascolizzato
Posts: 4
Joined: Sat Nov 08, 2014 10:09 am

Re: IX4-200d rebooting constantly

Post by vascolizzato » Sun Nov 09, 2014 5:59 pm

Mijzelf wrote:Did you read the thread?
i read the thread, but i can't understand well:D...
i haven't pinout on my board i have 10 soldered holes.
i have a pc with serial port can i connect with a serial cable where i sodered a wire on pin 2 -3 and 5? or can i use a usb to serial converter?

Mijzelf
Posts: 6194
Joined: Mon Jun 16, 2008 10:45 am

Re: IX4-200d rebooting constantly

Post by Mijzelf » Sun Nov 09, 2014 6:50 pm

You can't use a 'normal' serial port, you need a TTL signal. Something like this. And yes, then you can solder a wire on the mobo. GND, TX en RX are needed.

vascolizzato
Posts: 4
Joined: Sat Nov 08, 2014 10:09 am

Re: IX4-200d rebooting constantly

Post by vascolizzato » Tue Nov 11, 2014 7:28 pm

i'm waiting for ttl converter. thanks for reply! can i use putty to connect?

Mijzelf
Posts: 6194
Joined: Mon Jun 16, 2008 10:45 am

Re: IX4-200d rebooting constantly

Post by Mijzelf » Wed Nov 12, 2014 8:35 am

Yes.

tcollier
Posts: 1
Joined: Sun Sep 28, 2014 7:28 am

Re: IX4-200d rebooting constantly

Post by tcollier » Tue Dec 09, 2014 8:19 pm

I too have the same issues, a bricked iomega.
I have read this topic, and have bought a TTI Serial cable;
But I am confused to which pins I need to attach.

On my cable I have 6 cables on my TTI serial cable :

- White
- Green
- Yellow
- Orange
- Blue
- Black

Can someone tell me on which pin I need to connect which cable?
Greatly appreciated.

vascolizzato
Posts: 4
Joined: Sat Nov 08, 2014 10:09 am

Re: IX4-200d rebooting constantly

Post by vascolizzato » Sun Dec 14, 2014 6:26 pm

i received my ttl converter i connected it to right pin, but when i try to connect with putty i've only a black screen no text...???? :shock: :shock:

vincieh
Posts: 6
Joined: Wed May 27, 2015 12:43 pm

Re: IX4-200d rebooting constantly

Post by vincieh » Thu May 28, 2015 12:23 am

Hi All

I have a ix4-200d cloud edition and the bios update from usb failed. I too have repeated reboots . I have read the forum and have been successfully able to console into the machine. Ive followed everybody's commands for tftpboot, etc. everytime I get the bad magic error after about 5%. ive tried the files from ix4-200d-3.2.6.17887-recovery

I know this is an old thread but any assistance would be greatly appreciated. ive spend hours surfing the web and I don't think there is much of anything that I haven't tried that ive found so far

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.1 **

** MARVELL BOARD: IX4-110 LE

U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Found 0x20 i2c device
Set Power State as Always On
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
Found ADT7473, program LED ...(led_volt=90) OK
Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK

Marvell Serial ATA Adapter
Integrated Sata device found


CPU : Marvell Feroceon (Rev 1)
Found initrd at 0x2d8000

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is RGMII

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
flags: 64bit ncq stag led pmp slum part
scanning bus for devices...
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0xb0000, size 0x228000

Reading data from 0x2d7e00 -- 100% complete.
2260992 bytes read: OK

NAND read: device 0 offset 0x2d8000, size 0x2f0000

Reading data from 0x2fd800 -- 5% complete.reading NAND page at offset 0x304000 failed
3080192 bytes read: ERROR
## Booting image at 02000000 ...
Image Name: Linux-2.6.31.8
Created: 2012-02-13 21:48:28 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2077080 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 12000000 ...
Bad Magic Number▒

Post Reply