General NAS-Central Forums

Welcome to the NAS community
It is currently Thu Nov 23, 2017 11:42 pm

All times are UTC




Post new topic Reply to topic  [ 51 posts ]  Go to page 1, 2, 3, 4  Next
Author Message
 Post subject: LG n2r1d unbrick
PostPosted: Tue Oct 29, 2013 6:24 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
Hello,
can somebody help me to unbrick my lg nas,
i bought this from someone second hand.
when i power on it says boot fail. when i push left and right button with the power button it says netboot and i can choose to change the firmware and when i do that it never goes further and freeses.

SORRY for my worse english :D

i found this on the net and my question is can i unbrick it with this script? and how?


LG-NAS:~# fw_printenv
CRC: calced 5283b544, saved 5283b544
baudrate=115200
loads_echo=0
ipaddr=10.177.190.56
serverip=10.177.190.59
rootpath=/opt/Orion-SDK/armel-2.0/rootfs
netmask=255.255.254.0
console=console=ttyS0,115200 mtdparts=nand_mtd:0x100000@0(uboot),0x400000@0x100000(kernel),0xb00000@0x500000(rootfs),0x5000000@0x1000000(data)
CASset=min
MALLOC_len=1
ethprime=egiga0
bootroot_nfs=root=/dev/nfs rw
bootroot_mtd=root=/dev/mtdblock2 rootfstype=squashfs
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
boot_name=uboot.bin
root_name=flash_rootfs.sqsh
data_name=flash_data.sqsh
up_boot=tftp 2000000 $(boot_name); nand erase 0 100000; nand write.e 2000000 0 78000
up_kern=tftp 2000000 $(image_name); nand erase 100000 400000; nand write 2000000 100000 1d0000; bbm save
up_root=tftp 1000000 $(root_name); nand erase 500000 b00000; nand write 1000000 500000 $(filesize); bbm save
up_data=tftp 1000000 $(data_name); nand erase 1000000 5000000; nand write.e 1000000 1000000 $(filesize); bbm save
bootcmd_nfs=tftp 2000000 $(image_name); setenv bootargs $(console) $(bootroot_nfs) nfsroot=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvNetConfig) $(mvPhoneConfig); bootm 2000000
bootcmd_mtd=run read_kern; setenv bootargs $(console) $(bootroot_mtd) lpj=3973120; bootm 2000000
bootcmd_md=run read_kern; setenv bootargs $(console) root=/dev/md1 rw lpj=3973120; bootm 2000000
bootcmd_enc=run read_kern; setenv bootargs $(console) $(bootroot_mtd) enclosure lpj=3973120; bootm 2000000
bootcmd=run read_kern; setenv bootargs $(console) root=/dev/md1 rw lpj=3973120; bootm 2000000
autoload=no
read_kern=nand read.e 2000000 100000 1d0000
bootargs_usb=root=/dev/sdc2 rw rootdelay=10
bootcmd_usb=usb start; fatload usb 0:1 2000000 uimage; set bootargs $(console) $(bootargs_usb); bootm 2000000
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
ethact=egiga0
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=no
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=1
disaMvPnp=no
hddPowerCtrl=no
ethaddr=XX:XX:XX:XX:XX:XX


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Wed Oct 30, 2013 1:52 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6075
? That is not a script, it's a u-boot environment listing.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Wed Oct 30, 2013 4:00 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
Mijzelf wrote:
? That is not a script, it's a u-boot environment listing.


ok and what's that?
do you have an solution for me?
and where you from? netherland?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Wed Oct 30, 2013 6:42 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6075
zenelli wrote:
Mijzelf wrote:
? That is not a script, it's a u-boot environment listing.


ok and what's that?
It a list of configurable settings of the bootloader. (Or actually 'a' bootloader, as without any context I cannot say if these settings appy to your box)

Quote:
do you have an solution for me?
Not directly. As your box seems to be able to do rather complex things (show information in a display, react on button presses), I guess it's actually not bricked at all. It just needs some extra software on the harddisk to do it's full job.

Quote:
when i push left and right button with the power button it says netboot and i can choose to change the firmware and when i do that it never goes further and freeses.
I guess it's trying to download firmware from a tftp server. The question is, what is it exactly trying to download, and from which server?

You can connect the box directly to your PC, run wireshark on the PC to monitor the network interface, and try to do a netboot. The wireshark logs can give more information.

Have you already searched for the manual? Does it say anything about installing new disks?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Wed Oct 30, 2013 8:57 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
I guess it's trying to download firmware from a tftp server. The question is, what is it exactly trying to download, and from which server?

You can connect the box directly to your PC, run wireshark on the PC to monitor the network interface, and try to do a netboot. The wireshark logs can give more information.

Have you already searched for the manual? Does it say anything about installing new disks?


i have downloaded NC1 newui update tool 10094 and wanted to upgrade, but when i choose this it wants to upgrade but it newer begins.
and i think its looking for an server outside because when i have no internet it gives me an error.

i have attached the nas direct to my laptop with an ethernet cable
Must i have an hdd in to the nas for upgrading? and with wich format?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Thu Oct 31, 2013 9:54 am 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6075
zenelli wrote:
Must i have an hdd in to the nas for upgrading? and with wich format?
I guess so. The complete firmware won't fit in flash, so a part is installed on harddisk. And I *guess* the contents is not important, as the low level procedure will create new partitions. Be prepared that all data on that disk will be destroyed.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Sun Nov 03, 2013 7:15 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
So when the firmware upgrade doesn't work there is no other solution to make it work?
even with a serial cable hardflash?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 8:48 am 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6075
zenelli wrote:
So when the firmware upgrade doesn't work there is no other solution to make it work?
even with a serial cable hardflash?
Did you conclude that from something I wrote?

There are several ways to get it working, but it requires more knowledge about how it actually 'works' than simply using a Vendor tool to reinstall the firmware.

As I said, I don't think your box is bricked at all. When you could clone a disk of another N2R1D user, I guess it should work.

If you have a serial cable, the output while trying to use the Vendor tool might tell why it is failing.

And a serial cable gives more possibilities, like installing Debian or Arch.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 12:00 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
HI mijzelf,

i don't know somebody else with the same nas,
if you can tell me how i must connect the serial cable to read the nas wil be great


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 12:13 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6075
This one? http://www.nas-central.org/wiki/LG-N2B1 ... ort_Access


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 2:22 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
This is for an n2b1d it's make no difference?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 2:36 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6075
Don't know. A quick Google didn't reveal the actual difference between the N2R1D and N2B1D. As far as I can tell the boxes are identical. But you can open it. If it contains the same mainboard, the serial port is the same too, of course.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 3:50 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
i opened the case and its the same, so i can read the bootlouder with hyperterminal and see where it fails?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 6:36 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6075
That is the idea, yes.

BTW, it is clear to you that you can't just use an rs232 port? A 3.3V TTL connection is needed.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 6:42 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
hello,
i have read the bootlooder, this came out.


ðNormal mode boot start!

_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LGE-NAS BOARD: NC1 LE

U-Boot 1.1.4 (Feb 24 2012 - 15:06:45)NC1

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0700

Soc: 88F6192 A1 CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM (DDR2) CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:nand_bbm_init: Init nand bad block information...
nand_bbm_find_pos: nand_bbm_check = 0, erasesize = 20000
nand_bbm_find_pos: nand_bbm_find_pos: bbm pos = 7800000, pos = 7800000
Loading nand bad block info(07800000+00020000)...
nand_bbm_info_load: bbm->magic = 8192a5a7
nand_bbm_info_load: bbm->bb_count = 0
nand_bbm_info_load: bbm->assign_index = 3ff
Assign index = 3ff
nand_bbm_info_load: Loading nand bad block info...ok
128 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Normal mode : lg_bootmode = 0
Hit any key to stop autoboot: 0

Reset IDE:
Marvell Serial ATA Adapter, MAX_DEVICE=32
Integrated Sata device found
Channel 1/2 is connected ...
Port Multiplier found @ 0 1. Vendor: 11ab ports: 4
[0 1 2]: Enable DMA mode (5)
Device 3 @ 0 1 2:
Model: HL-DT-ST DVDRAM GH50N Firm: R106 Ser#: K2JB37I1420

Type: Removable CD ROM
Capacity: not available

** Bad partition 1 **
** Bad partition 1 **

5 bytes read
## Booting image at 02000000 ..., header_size = 00000040, header_addr = 0069024c

image_header_t hdr contents
hdr->ih_magic = 56190527, hdr->ih_hcrc = b48fdb3d
hdr->ih_time = 358deb4c, hdr->ih_size = 001c4c6c
hdr->ih_load = 00800000, hdr->ih_ep = 00800000
hdr->ih_dcrc = c5261ba1
hdr->ih_os = 05, hdr->ih_arch = 02
hdr->ih_type = 02, hdr->ih_comp = 00
hdr->ih_name = Linux-2.6.22.18

Image Name: Linux-2.6.22.18
Created: 2010-11-23 9:45:25 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1854572 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................
......................................................... done, booting the kern
el.
[ 0.000000] Linux version 2.6.22.18 (root@anyong-desktop) (gcc version 4.2.0
20070413 (prerelease)) #4 Tue Nov 23 18:45:21 KST 2010
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 s
ets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 s
ets
[ 0.000000] Built 1 zonelists. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100
000@0(uboot),0x400000@0x100000(kernel),0xb00000@0x500000(rootfs),0x5000000@0x100
0000(data) root=/dev/md0 rw lpj=4964352 nas_type=0x00000210
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total
[ 0.000000] Memory: 125952KB available (3436K code, 252K data, 104K init)
[ 0.000000] Calibrating delay loop (skipped)... 992.87 BogoMIPS preset
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] NET: Registered protocol family 16
[ 0.010000]
[ 0.010000] CPU Interface
[ 0.010000] -------------
[ 0.010000] SDRAM_CS0 ....base 00000000, size 128MB
[ 0.010000] SDRAM_CS1 ....disable
[ 0.010000] SDRAM_CS2 ....disable
[ 0.010000] SDRAM_CS3 ....disable
[ 0.010000] PEX0_MEM ....base e8000000, size 128MB
[ 0.010000] PEX0_IO ....base f2000000, size 1MB
[ 0.010000] INTER_REGS ....base f1000000, size 1MB
[ 0.010000] NFLASH_CS ....base fa000000, size 2MB
[ 0.010000] SPI_CS ....base f4000000, size 16MB
[ 0.010000] BOOT_ROM_CS ....no such
[ 0.010000] DEV_BOOTCS ....no such
[ 0.010000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.010000]
[ 0.010000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- R
D-88F6192A-NAS Soc: 88F6192 A1 LE
[ 0.010000]
[ 0.010000] Detected Tclk 166666667 and SysClk 200000000
[ 0.010000] MV Buttons Device Load
[ 0.010000] Marvell USB EHCI Host controller #0: c052d600
[ 0.630000] PEX0 interface detected no Link.
[ 0.630000] PCI: bus0: Fast back to back transfers enabled
[ 0.630000] SCSI subsystem initialized
[ 0.630000] usbcore: registered new interface driver usbfs
[ 0.640000] usbcore: registered new interface driver hub
[ 0.640000] usbcore: registered new device driver usb
[ 0.640000] NET: Registered protocol family 2
[ 0.650000] Time: kw_clocksource clocksource has been installed.
[ 0.730000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.730000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.730000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.730000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.730000] TCP reno registered
[ 0.770000] TWSI: mvTwsiStartBitSet repeated start Bit
[ 0.810000] TWSI: mvTwsiStartBitSet repeated start Bit
[ 0.830000] RTC registered
[ 0.830000] Use the XOR engines (acceleration) for enhancing the following fu
nctions:
[ 0.830000] o RAID 5 Xor calculation
[ 0.830000] o kernel memcpy
[ 0.830000] o kenrel memzero
[ 0.830000] o copy user to/from kernel buffers
[ 0.830000] Number of XOR engines to use: 4
[ 0.830000] cesadev_init(c000c9a4)
[ 0.830000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.840000] Warning: TS unit is powered off.
[ 0.840000] VFS: Disk quotas dquot_6.5.1
[ 0.840000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.840000] squashfs: version 3.4 (2008/08/26) Phillip Lougher
[ 0.840000] Starting Selective Mirror Daemon...
[ 0.840000] /proc/s_mirror created !!!!!!!!!!!!!!!!!!!
[ 0.850000] io scheduler noop registered
[ 0.850000] io scheduler anticipatory registered
[ 0.850000] io scheduler deadline registered
[ 0.850000] io scheduler cfq registered (default)
[ 0.860000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
disabled
[ 0.860000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.870000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 0.870000] Loading Marvell Ethernet Driver:
[ 0.880000] o Cached descriptors in DRAM
[ 0.880000] o DRAM SW cache-coherency
[ 0.890000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.890000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.900000] o TCP segmentation offload enabled
[ 0.900000] o Receive checksum offload enabled
[ 0.910000] o Transmit checksum offload enabled
[ 0.910000] o Network Fast Processing (Routing) supported
[ 0.920000] o Driver ERROR statistics enabled
[ 0.920000] o Driver INFO statistics enabled
[ 0.930000] o Proc tool API enabled
[ 0.930000] o Rx descripors: q0=128
[ 0.930000] o Tx descripors: q0=532
[ 0.940000] o Loading network interface(s):
[ 0.940000] o eth0, ifindex = 1, GbE port = 0
[ 0.950000]
[ 0.950000] Warning: Giga 1 is Powered Off
[ 0.960000]
[ 0.960000] mvFpRuleDb (c7cae000): 1024 entries, 4096 bytes
[ 0.960000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 0.970000] Copyright (c) 1999-2006 Intel Corporation.
[ 0.970000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 0.980000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 0.990000] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn
.edu>
[ 0.990000] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393
@maroon.tc.umn.edu>
[ 1.000000] Integrated Sata device found
[ 1.030000] scsi0 : Marvell SCSI to SATA adapter
[ 1.040000] scsi1 : Marvell SCSI to SATA adapter
[ 1.540000] [0 1] CHANNEL_PM_INIT_DEVICES port:0 status:0
[ 1.540000] [0 1] CHANNEL_PM_INIT_DEVICES port:2 status:2
[ 1.540000] [0 1] CHANNEL_PM_INIT_DEVICES port:2 status:3
[ 1.540000] [0 1] CHANNEL_PM_INIT_DEVICES port:2 status:4
[ 1.540000] [0 1] CHANNEL_PM_INIT_DEVICES port:3 status:0
[ 1.560000] scsi 1:0:2:0: CD-ROM HL-DT-ST DVDRAM GH50N R106 PQ
: 0 ANSI: 0
[ 2.450000] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda
tray
[ 2.450000] Uniform CD-ROM driver Revision: 3.20
[ 2.460000] sr 1:0:2:0: Attached scsi generic sg0 type 5
[ 2.470000] NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND
128MiB 3,3V 8-bit)
[ 2.470000] nand_bbm_init: Init nand bad block information...
[ 2.480000] nand_bbm_find_pos: nand_bbm_check = 0, erasesize = 20000
[ 2.490000] nand_bbm_find_pos: nand_bbm_find_pos: bbm pos = 7800000, pos = 78
00000
[ 2.490000] Loading nand bad block info(07800000+00020000)...
[ 2.530000] nand_bbm_info_load: bbm->magic = 8192a5a7
[ 2.540000] nand_bbm_info_load: bbm->bb_count = 0
[ 2.550000] nand_bbm_info_load: bbm->assign_index = 3ff
[ 2.550000] Assign index = 3ff
[ 2.550000] nand_bbm_info_load: Loading nand bad block info...ok
[ 2.560000] 4 cmdlinepart partitions found on MTD device nand_mtd
[ 2.570000] Using command line partition definition
[ 2.570000] Creating 4 MTD partitions on "nand_mtd":
[ 2.580000] 0x00000000-0x00100000 : "uboot"
[ 2.580000] 0x00100000-0x00500000 : "kernel"
[ 2.590000] 0x00500000-0x01000000 : "rootfs"
[ 2.600000] 0x01000000-0x06000000 : "data"
[ 2.650000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 2.660000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned
bus number 1
[ 2.700000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 2.720000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driv
er 10 Dec 2004
[ 2.720000] usb usb1: configuration #1 chosen from 1 choice
[ 2.730000] hub 1-0:1.0: USB hub found
[ 2.730000] hub 1-0:1.0: 1 port detected
[ 2.850000] Initializing USB Mass Storage driver...
[ 3.130000] usb 1-1: new high speed USB device using ehci_marvell and address
2
[ 3.280000] usb 1-1: configuration #1 chosen from 1 choice
[ 3.280000] hub 1-1:1.0: USB hub found
[ 3.290000] hub 1-1:1.0: 4 ports detected
[ 3.400000] usbcore: registered new interface driver usb-storage
[ 3.400000] USB Mass Storage support registered.
[ 3.410000] mice: PS/2 mouse device common for all mice
[ 3.410000] i2c /dev entries driver
[ 3.420000] md: linear personality registered for level -1
[ 3.420000] md: raid0 personality registered for level 0
[ 3.430000] md: raid1 personality registered for level 1
[ 3.430000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-d
evel@redhat.com
[ 3.440000] sdhci: Secure Digital Host Controller Interface driver
[ 3.450000] sdhci: Copyright(c) Pierre Ossman
[ 3.450000] TCP cubic registered
[ 3.450000] NET: Registered protocol family 1
[ 3.460000] NET: Registered protocol family 17
[ 3.460000] NET: Registered protocol family 5
[ 3.540000] md: Autodetecting RAID arrays.
[ 3.540000] md: autorun ...
[ 3.540000] md: ... autorun DONE.
[ 3.550000] EXT3-fs: unable to read superblock
[ 3.550000] SQUASHFS error: sb_bread failed reading block 0x1
[ 3.560000] romfs: unable to read superblock
[ 3.560000] List of all partitions:
[ 3.560000] 0b00 1048575 sr0 driver: sr
[ 3.570000] 1f00 1024 mtdblock0 (driver?)
[ 3.570000] 1f01 4096 mtdblock1 (driver?)
[ 3.580000] 1f02 11264 mtdblock2 (driver?)
[ 3.580000] 1f03 81920 mtdblock3 (driver?)
[ 3.590000] No filesystem could mount root, tried: ext3 squashfs romfs
[ 3.590000] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno
wn-block(9,0)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 51 posts ]  Go to page 1, 2, 3, 4  Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group