General NAS-Central Forums

Welcome to the NAS community
It is currently Sat May 27, 2017 7:27 pm

All times are UTC




Post new topic Reply to topic  [ 51 posts ]  Go to page Previous  1, 2, 3, 4  Next
Author Message
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 7:51 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5995
There are a few strange things here. You told you could get some texts on an LCD display, but this boot ended in a kernel panic, so it won't do anything anymore (until reboot).

According to the kernel command line
Code:
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000@0(uboot),0x400000@0x100000(kernel),0xb00000@0x500000(rootfs),0x5000000@0x1000000(data) root=/dev/md0 rw lpj=4964352 nas_type=0x00000210
the kernel should search it's rootfs on /dev/md0, which is a raid array. Yet the box also has a rootfs in flash (11MiB in size) and a 'data' partition 80MiB. I guess you should be holding some key pressed on boot to let it boot from flash. And I guess that 80MiB 'data' partition should contain basic stuff to initialize the harddisk(s). The difference should be visible in the bootlog.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Mon Nov 04, 2013 9:13 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
lcd gives only boot failure when i push power button and when i push left and right with the power button it says netboot.
this log is with only the power button (whitout hdd) i don't know if it give me a log when i set the nas in to netboot


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Tue Nov 05, 2013 9:13 am 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5995
Can you stop the bootprocess by
Code:
Hit any key to stop autoboot: 0
and then post the output of 'printenv' ?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Tue Nov 05, 2013 4:17 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
hmmm,
how must i do that?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Tue Nov 05, 2013 6:19 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5995
Assuming your serial port works in 2 directions, you can stop the default bootprocess by hitting any key when the text 'Hit any key to stop autoboot' appears.
Then you'll get a prompt, the u-boot prompt, on which you can execute command. Like printenv and help.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Wed Nov 06, 2013 6:46 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
here it is:

ðNormal mode boot start!

_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LGE-NAS BOARD: NC1 LE

U-Boot 1.1.4 (Feb 24 2012 - 15:06:45)NC1

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0700

Soc: 88F6192 A1 CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM (DDR2) CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:nand_bbm_init: Init nand bad block information...
nand_bbm_find_pos: nand_bbm_check = 0, erasesize = 20000
nand_bbm_find_pos: nand_bbm_find_pos: bbm pos = 7800000, pos = 7800000
Loading nand bad block info(07800000+00020000)...
nand_bbm_info_load: bbm->magic = 8192a5a7
nand_bbm_info_load: bbm->bb_count = 0
nand_bbm_info_load: bbm->assign_index = 3ff
Assign index = 3ff
nand_bbm_info_load: Loading nand bad block info...ok
128 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Normal mode : lg_bootmode = 0
Hit any key to stop autoboot: 0
LGE-NAS>> printenv
Unknown command 'printenv' - try 'help'
LGE-NAS>> help
? - alias for 'help'
base - print or set address offset
bbm - nand bad block management
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bubt - Burn an image on the Boot Nand Flash.
chpart - change active partition
cmp - memory compare
cmpm - Compare Memory
cp - memory copy
cpumap - Display CPU memory mapping settings.
crc32 - checksum calculation
date - get/set/reset date & time
dclk - Display the MV device CLKs.
dhcp - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo - echo args to console
eeprom - EEPROM sub-system
erase - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2load2- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
print information about filesystemload binary file from a dos filesystemlist fil
es in a directory (default /)fi - Find value in the memory.
flinfo - print FLASH memory information
fsinfo - print information about filesystems
fsload - load binary file from a filesystem image
g - start application at cached address 'addr'(default addr 0x40000)
go - start application at address 'addr'
help - print online help
icrc32 - checksum calculation
ide - IDE sub-system
iloop - infinite loop on address range
imd - i2c memory display
iminfo - print header information for application image
imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing)
imw - memory write (fill)
inm - memory modify (constant address)
iprobe - probe to discover valid I2C chip addresses
ir - reading and changing MV internal register values.
lgdiag - Check the LG Board Diag.
loop - infinite loop on address range
ls - list files in a directory (default /)
map - Diasplay address decode windows
md - memory display
me - PCI master enable
mm - memory modify (auto-incrementing)
mmcinit - init mmc card
mp - map PCI BAR
mtdparts- define flash/nand partitions
mtest - simple RAM test
mw - memory write (fill)
nand - NAND sub-system
nasd - Interface with LG NAS Detector
nboot - boot from NAND device
nbubt - Burn a boot loader image on the Boot Nand Flash.
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
phyRead - Read PCI-E Phy register
pciePhyWrite - Write PCI-E Phy register
phyBist [Phy model] [mode:1,2,4,3]
phyRead - Read Phy register
phyWrite - Write Phy register
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr - Satrt recovery process (Distress Beacon with TFTP server)
reset - Perform RESET of the CPU
resetenv - Return all environment variable to default.
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
scsi - SCSI sub-system
scsiboot- boot from SCSI device
se - PCI Slave enable
setenv - set environment variables
sflash - read, write or erase the external SPI Flash.
sg - scanning the PHYs status
sp - Scan PCI bus.
switchRegRead - Read switch register
switchRegWrite - Write switch register
Temp - read chip Tj temp
tftpboot- boot image via network using TFTP protocol
usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
LGE-NAS>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.177.190.56
serverip=10.177.190.59
rootpath=/opt/Orion-SDK/armel-2.0/rootfs
netmask=255.255.254.0
console=console=ttyS0,115200 mtdparts=nand_mtd:0x100000@0(uboot),0x400000@0x1000
00(kernel),0xb00000@0x500000(rootfs),0x5000000@0x1000000(data)
CASset=min
MALLOC_len=1
ethprime=egiga0
bootroot_nfs=root=/dev/nfs rw
bootroot_mtd=root=/dev/mtdblock2 rootfstype=squashfs
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
boot_name=uboot.bin
root_name=flash_rootfs.sqsh
data_name=flash_data.sqsh
up_boot=tftp 2000000 $(boot_name); nand erase 0 100000; nand write.e 2000000 0 7
8000
up_kern=tftp 2000000 $(image_name); nand erase 100000 400000; nand write 2000000
100000 1d0000; bbm save
up_root=tftp 1000000 $(root_name); nand erase 500000 b00000; nand write 1000000
500000 $(filesize); bbm save
up_data=tftp 1000000 $(data_name); nand erase 1000000 5000000; nand write.e 1000
000 1000000 $(filesize); bbm save
bootcmd_nfs=tftp 2000000 $(image_name); setenv bootargs $(console) $(bootroot_nf
s) nfsroot=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvN
etConfig) $(mvPhoneConfig); bootm 2000000
bootcmd_mtd=run read_kern; setenv bootargs $(console) $(bootroot_mtd) lpj=397312
0; bootm 2000000
bootcmd_md=run read_kern; setenv bootargs $(console) root=/dev/md1 rw lpj=397312
0; bootm 2000000
bootcmd_enc=run read_kern; setenv bootargs $(console) $(bootroot_mtd) enclosure
lpj=3973120; bootm 2000000
autoload=no
read_kern=nand read.e 2000000 100000 1d0000
bootargs_usb=root=/dev/sdc2 rw rootdelay=10
bootcmd_usb=usb start; fatload usb 0:1 2000000 uimage; set bootargs $(console) $
(bootargs_usb); bootm 2000000
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
ethact=egiga0
ethaddr=00:E0:91:81:A4:98
nas_type=0x00000210
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=no
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootargs_nfs=root=/dev/nfs rw
root_path=root=/dev/md0 rw
read-kern=ide reset; ext2load2 ide 2 2000000 /boot/$(image_name);
mem-clear=mw.l 1000000 0x00000000 1000000
bootcmd_hdd=run read-kern; setenv bootargs $(console) $(root_path) lpj=4964352 n
as_type=$(nas_type); bootm 0x2000000;
bootargs_ram=root=/dev/ram0 rw
tftp-ram=tftp 1000000 nt/$(uImage-ram); tftp 2000000 nt/ramdisk_image; set boota
rgs $(console) $(bootargs_ram); bootm 1000000 2000000
uImage-ram=uImage-2.6.30-nt1_11_ramdisk
bootcmd_nand=nand read.e 2000000 100000 1d0000; setenv bootargs $(console) root=
/dev/md1 rw lpj=3973120; bootm 0x2000000
bootcmd=run bootcmd_hdd; run bootcmd_nand
bootcmd_tftp=tftp 0x2000000 $(image_name); setenv bootargs $(console) $(root_pat
h) lpj=4964352; bootm 0x2000000;
firmware=firmware.tar.gz
bootcmd_netenc=set bootargs $(console) $(bootargs_ram) netenc nas_type=$(nas_typ
e) IP=$(ipaddr) SIP=$(serverip) FW=$(firmware); bootm 1000000 2000000
bootcmd_usbenc=set bootargs $(console) $(bootargs_ram) usbenc nas_type=$(nas_typ
e) IP=$(ipaddr) SIP=$(serverip) FW=$(firmware); bootm 1000000 2000000
bootdelay=1
disaMvPnp=no
hddPowerCtrl=no
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
image_multi=yes
enaAutoRecovery=no
pcieTune=no

Environment size: 3362/131068 bytes
LGE-NAS>>


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Wed Nov 06, 2013 7:53 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5995
That is strange.

In the environment is the value
Code:
bootcmd=run bootcmd_hdd; run bootcmd_nand
Which means that in a default uninterrupted boot it will execute command bootcmd_hdd, and if that fails bootcmd_nand.

bootcmd_hdd does
Code:
bootcmd_hdd=run read-kern; setenv bootargs $(console) $(root_path) lpj=4964352 nas_type=$(nas_type); bootm 0x2000000;
It executes read-kern, which tries to read a kernel from harddisk (read-kern=ide reset; ext2load2 ide 2 2000000 /boot/$(image_name);), then sets some bootargs (which will be applied to the kernel as command line), and finally boots the image at memory address 0x2000000 (put there by read-kern).
If bootcmd_hdd fails, u-boot tries bootcmd_nand:
Code:
bootcmd_nand=nand read.e 2000000 100000 1d0000; setenv bootargs $(console) root=/dev/md1 rw lpj=3973120; bootm 0x2000000
which tries to load a kernel from nand, sets bootargs, and boots the image.

The strange thing is, bootcmd_hdd sets root=/dev/md0, while bootcmd_nand sets root=/dev/md1. Your bootlog in the previous page has in the cmdline root=/dev/md0. So that says the kernel was load from harddisk, but in the bootlog I see no trace of a harddisk.
Another strange thing: Why specifies bootcmd_nand /dev/md1? That is a raid array, which is on a harddisk. But that harddisk isn't there, else we shouldn't need to load a kernel from nandflash.

I suggest to try to use the rootfs in /dev/mtdblock2.

Interrupt the boot, and execute the commands
Code:
nand read.e 2000000 100000 1d0000
setenv bootargs $(console) root=/dev/mtdblock2 ro lpj=3973120
bootm 0x2000000
I think this will bring the box to a rescue mode, where it will try to initialize a harddisk. The bootlog will tell.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Wed Nov 06, 2013 8:16 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
must i put an harddisk in the nas?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Wed Nov 06, 2013 8:49 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
this came out with an hdd in it:

LGE-NAS>> nand read. e 2000000 100000 1d0000
Usage:
nand - NAND sub-system

LGE-NAS>> setenv bootargs $ (console) root=/dev/mtdblock2 ro lpj=3973120
LGE-NAS>> bootm 0x2000000
## Booting image at 02000000 ..., header_size = 00000040, header_addr = 0069024c

image_header_t hdr contents
hdr->ih_magic = 56190527, hdr->ih_hcrc = b48fdb3d
hdr->ih_time = 358deb4c, hdr->ih_size = 001c4c6c
hdr->ih_load = 00800000, hdr->ih_ep = 00800000
hdr->ih_dcrc = c5261ba1
hdr->ih_os = 05, hdr->ih_arch = 02
hdr->ih_type = 02, hdr->ih_comp = 00
hdr->ih_name = Linux-2.6.22.18

Image Name: Linux-2.6.22.18
Created: 2010-11-23 9:45:25 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1854572 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... Bad Data CRC, checksum = 9595eb8e, hdr->ih_dcrc = c526
1ba1
LGE-NAS>>


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Thu Nov 07, 2013 8:18 am 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5995
You made a typo:
Code:
nand read. e 2000000 100000 1d0000
should be
Code:
nand read.e 2000000 100000 1d0000
An indication for that is the 'Usage:
nand - NAND sub-system' which indicates a syntax/usage error. (Without telling how it should be, but hey, it's a low level bootloader. Not much room for a build-in manual)


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Thu Nov 07, 2013 6:34 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
this?

ðNormal mode boot start!

_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LGE-NAS BOARD: NC1 LE

U-Boot 1.1.4 (Feb 24 2012 - 15:06:45)NC1

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0700

Soc: 88F6192 A1 CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM (DDR2) CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:nand_bbm_init: Init nand bad block information...
nand_bbm_find_pos: nand_bbm_check = 0, erasesize = 20000
nand_bbm_find_pos: nand_bbm_find_pos: bbm pos = 7800000, pos = 7800000
Loading nand bad block info(07800000+00020000)...
nand_bbm_info_load: bbm->magic = 8192a5a7
nand_bbm_info_load: bbm->bb_count = 0
nand_bbm_info_load: bbm->assign_index = 3ff
Assign index = 3ff
nand_bbm_info_load: Loading nand bad block info...ok
128 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Normal mode : lg_bootmode = 0
Hit any key to stop autoboot: 0
LGE-NAS>> nand read.e 2000000 100000 1d0000

NAND read: device 0 offset 0x100000, size 0x1d0000

Reading data from 0x2cf800 -- 100% complete.
1900544 bytes read: OK
LGE-NAS>> setenv bootargs $ (console) root=/dev/mtdblock2 ro lpj3973120
LGE-NAS>> bootm 0x2000000
## Booting image at 02000000 ..., header_size = 00000040, header_addr = 0069024c

image_header_t hdr contents
hdr->ih_magic = 56190527, hdr->ih_hcrc = b48fdb3d
hdr->ih_time = 358deb4c, hdr->ih_size = 001c4c6c
hdr->ih_load = 00800000, hdr->ih_ep = 00800000
hdr->ih_dcrc = c5261ba1
hdr->ih_os = 05, hdr->ih_arch = 02
hdr->ih_type = 02, hdr->ih_comp = 00
hdr->ih_name = Linux-2.6.22.18

Image Name: Linux-2.6.22.18
Created: 2010-11-23 9:45:25 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1854572 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................
......................................................... done, booting the kern
el.


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Thu Nov 07, 2013 8:36 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5995
And that's it? How disappointing. There must be something wrong, but I don't see it. As this kernel is the same one which booted earlier, I can only guess somehow the bootlog is redirected elsewhere. (BTW, that is done by the 'console=NNN' in the commandline. Unfortunately we can't see the commandline, only guess how it looks).

Do you have a disk inside, and did you see any activity?


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Thu Nov 07, 2013 9:33 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
yes there was an disk inside and i saw lights were blinking


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Fri Nov 08, 2013 10:18 am 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 5995
Ah. So there is a good chance it has initialized the disk now.

BTW, have you seen this?
https://web.archive.org/web/20130425133 ... tryID=6513


Top
 Profile  
 
 Post subject: Re: LG n2r1d unbrick
PostPosted: Fri Nov 08, 2013 6:51 pm 
Offline

Joined: Tue Oct 29, 2013 5:38 pm
Posts: 26
yeah i done that but its same firmware doesnt begins, i was forgot to say after doing the last commands you give me then the nas was again boot failure.
i have put the nas into netboot to try again firmware with serial attacheged you can see on the log.

ðonly left and right buttons are pushed
Network Enclosure mode boot start!

_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LGE-NAS BOARD: NC1 LE

U-Boot 1.1.4 (Feb 24 2012 - 15:06:45)NC1

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0700

Soc: 88F6192 A1 CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM (DDR2) CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:nand_bbm_init: Init nand bad block information...
nand_bbm_find_pos: nand_bbm_check = 0, erasesize = 20000
nand_bbm_find_pos: nand_bbm_find_pos: bbm pos = 7800000, pos = 7800000
Loading nand bad block info(07800000+00020000)...
nand_bbm_info_load: bbm->magic = 8192a5a7
nand_bbm_info_load: bbm->bb_count = 0
nand_bbm_info_load: bbm->assign_index = 3ff
Assign index = 3ff
nand_bbm_info_load: Loading nand bad block info...ok
128 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
ENCLOSURE mode : lg_bootmode = 1
Starting Network Enclosing...
is_usbenc() check usbenc
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found

[Packet len=306] IP [005ffe1cI4 -> 005ffe18I4] (68->67)

[Packet len=306] IP [005ffe1cI4 -> 005ffe18I4] (68->67)

[Packet len=306] IP [005ffe1cI4 -> 005ffe18I4] (68->67)

[Packet len=530] IP [005ffe1cI4 -> 005ffe18I4] (24988->24988)
<Request Info [r]>

[Packet len=530] IP [005ffe1cI4 -> 005ffe18I4] (24988->24988)
<Request Info [r]>

[Packet len=306] IP [005ffe1cI4 -> 005ffe18I4] (68->67)

[Packet len=530] IP [005ffe1cI4 -> 005ffe18I4] (24988->24988)
<Request Info [r]>

[Packet len=306] IP [005ffe1cI4 -> 005ffe18I4] (68->67)

[Packet len=530] IP [005ffe1cI4 -> 005ffe18I4] (24988->24988)
opcode:w nas's mac 00:50:43:00:02:02: opcode:w detector send mac 00:50:43:00:
02:02: <Static IP Setup [w]>
New IP : 005ffdecI4

[Packet len=306] IP [005ffe1cI4 -> 005ffe18I4] (68->67)

[Packet len=530] IP [005ffe1cI4 -> 005ffe18I4] (24988->24988)
<Request Info [r]>

[Packet len=530] IP [005ffe1cI4 -> 005ffe18I4] (24988->24988)
<Request Info [r]>

[Packet len=530] IP [005ffe1cI4 -> 005ffe18I4] (24988->24988)
<Request Info [r]>

[Packet len=306] IP [005ffe1cI4 -> 005ffe18I4] (68->67)

[Packet len=530] IP [005ffe1cI4 -> 005ffe18I4] (24988->24988)
opcode:U nas's mac 00:50:43:00:02:02: opcode:U detector send mac 00:50:43:00:
02:02: <FW Update Start [U]>
srv_desc: uImage initrd.gz firmware-nc1_10094rfke.bin
uimage: uImage
initrd: initrd.gz
firmware: firmware-nc1_10094rfke.bin
Using egiga0 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.200
Filename 'uImage'.
Load address: 0x1000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Hit any key to stop autoboot: 0
Unknown command 'no' - try 'help'
LGE-NAS>>


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 51 posts ]  Go to page Previous  1, 2, 3, 4  Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group