General NAS-Central Forums

Welcome to the NAS community
It is currently Fri Dec 15, 2017 9:51 pm

All times are UTC




Post new topic Reply to topic  [ 241 posts ]  Go to page Previous  1 ... 12, 13, 14, 15, 16, 17  Next
Author Message
PostPosted: Sun Jul 27, 2014 7:50 pm 
Offline

Joined: Fri Feb 08, 2013 2:12 am
Posts: 1
Inoxidable wrote:
At last! Finally I could install the firmware on the disk.

In fact, I have done both a 500GB and 1TB one, which you can install on any disk.

The problem is the newroot.lzma, it appears that you have in the dwnload site does not work.

This was the kit of the matter (Is in red):

Noxes wrote:
1. Download Iomega_HMNHD.lzma from download site

2. Delete all the partitions by Attaching the HDD a to usb to sata enclosure, attach in windows, open up cmd, use DiskPart -> list disk -> select disk 'x' -> clean = this removes the gpt file system.

3. Boot into Ubuntu -> open terminal - sudo -s then enter password = give u root constantly

4. Transfer lzma file by = cat /mypath/Iomega_HMNHD.lzma | lzma -d | dd of=/dev/sdx bs=1M (Can drag and drop the Iomega_HMNHD.lzma file into terminal which will give the full path and then add commands.)

5 In terminal -> fdisk- > fdisk -l (list and double check which drive it is. fdisk to the drive eg. fdisk /dev/sdc) -> warning about gpt not supported -> press d to delete the only partition, save and exit.

6 Put drive back into nas, after a while all the lights might go off.

7 Prepare an external usb disk/flash drive fat32 formatted with the tutorial at http://iomega.nas-central.org/wiki/Reco ... edia_CE%29
(keep the reset button pressed untill the there is activity on the flash/disk drive attached to the nas)

8 Once activity starts, wait untill the nas shuts itself down(very suddenly, thought it burned out) remove flash/disk drive, remove power plug, put it back in and let it power up and finish ~3 minutes

9 Should be able to connect to the webinterface with shares available and proper space available. (1.8TB)


With "newroot.lzma" could not load the firmware.

The disc does not stop, could not read the stick, there was no access. In short, all problems were.

But hey, you are finished.

As you can see, is installed on a 500GB disk. It works perfectly.

Now I can have a spare disk. In case of disaster.

Image

I'll be eternally grateful, Noxes. :D :D :D (Of course I also thank the people who made the recovery Wiki, which is very well done and explained).

Great, great, great, great! .....


Top
 Profile  
 
PostPosted: Thu Nov 27, 2014 5:55 pm 
Offline

Joined: Thu Nov 27, 2014 5:47 pm
Posts: 1
successfuly replaced hard drive in my iomega home CE to WD Blue 500g 7200. Used gparted linux on usb.


Top
 Profile  
 
PostPosted: Wed Jan 07, 2015 12:52 pm 
Offline

Joined: Wed Jan 07, 2015 12:47 pm
Posts: 6
Can you upgrade to a larger HD ?

I have a New out of the box 1TB nas, that I swapped the drive for a 3GB.

I have written the firmware and then rebooted from the USB stick, giving the following output:-

Code:
Stage-1 Bootloader Mon Feb  7 16:35:00 MST 2011
Attempting to set PLLA to 600MHz ...
  plla_ctrl0 : 0x0000021A
  plla_ctrl1 : 0x00480000
  plla_ctrl2 : 0x008F008B
  plla_ctrl3 : 0x00000154
PLLA Set

Setup memory, testing
Reading disk 0, Image 0
  Sector : 0x0000009A
  Hdr len: 0x00019480
  Hdr CRC: 0x94C61658
 OK
Initialising disks
SATA PHY not ready for device 1
Detecting SATA busses:
Bus 0: Found first device OK
  Device 0: Model: ST3000DM001-1CH166 Firm: CC27 Ser#: Z1F52T31
            Type: Hard Disk
            Capacity: 131071.9 MB = 127.9 GB (268435455 x 512)
  Device 1: not available
Environment successfully read from disk 0 primary image


U-Boot 1.1.2 (Jun  9 2011 - 14:14:20)

U-Boot code: 60D00000 -> 60D19480  BSS: -> 60D1D110
RAM Configuration:
        Bank #0: 60000000 256 MB
SRAM Configuration:
        64KB at 0x50000000
In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value

IDE read: device 0 block # 288, count 1 ... 1 blocks read: OK
Hit any key to stop autoboot:  0

IDE device 0: Model: ST3000DM001-1CH166 Firm: CC27 Ser#: Z1F52T31
            Type: Hard Disk
            Capacity: 131071.9 MB = 127.9 GB (268435455 x 512)
... is now current device

IDE read: device 0 block # 1290, count 5700 ... 5700 blocks read: OK

IDE read: device 0 block # 16674, count 5700 ... 5700 blocks read: OK
## Booting image at 60500000 ...
   Image Name:   Linux-2.6.31.14
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2189148 Bytes =  2.1 MB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 60800000 ...
   Image Name:
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    2788557 Bytes =  2.7 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux..................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.14 (soho@bsoho135.lss.emc.com) (gcc version 4.3.2 (crosstool-NG-1.3.1) ) #1 SMP Mon Feb 13 17:02:45 EST 2012
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Oxsemi NAS
[    0.000000] 1 memory region
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=/dev/md0 console=ttyS0,115200 elevator=cfq mem=256M poweroutage=yes mac_adr=0x00,0xd0,0xb8,0x19,0x4d,0x36
[    0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 252544KB available (3768K code, 275K data, 136K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:96
[    0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[    0.000000] ox820_clocksource_init() Timer 2 running at 390625 Hz
[    0.010000] Console: colour dummy device 80x30
[    0.010000] console [ttyS0] enabled
[    0.020000] Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
[    0.260000] Security Framework initialized
[    0.260000] Mount-cache hash table entries: 512
[    0.270000] CPU: Testing write buffer coherency: ok
[    0.270000] Calibrating local timer... 300.00MHz.
[    0.340000] CPU1: Booted secondary processor
[    0.440000] Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
[    0.680000] Brought up 2 CPUs
[    0.690000] SMP: Total of 2 processors activated (478.41 BogoMIPS).
[    0.700000] NET: Registered protocol family 16
[    0.700000] Number of DMA channels = 4, version = 4
[    0.710000] Reserving a DMA channel for ODRB
[    0.710000] Allocating 475 SRAM generic DMA descriptors
[    0.730000] bio: create slab <bio-0> at 0
[    0.740000] SCSI subsystem initialized
[    0.740000] usbcore: registered new interface driver usbfs
[    0.750000] usbcore: registered new interface driver hub
[    0.760000] usbcore: registered new device driver usb
[    0.790000] NET: Registered protocol family 2
[    0.790000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.800000] Switched to NOHz mode on CPU #0
[    0.800000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.800000] Switched to NOHz mode on CPU #1
[    0.810000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.820000] TCP: Hash tables configured (established 8192 bind 8192)
[    0.820000] TCP reno registered
[    0.830000] NET: Registered protocol family 1
[    0.830000] Trying to unpack rootfs image as initramfs...
[    0.840000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    0.880000] Freeing initrd memory: 2720K
[    0.880000] Create fragment cache
[    0.890000] fuse init (API version 7.12)
[    0.890000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    0.900000] msgmni has been set to 499
[    0.910000] alg: No test for stdrng (krng)
[    0.910000] io scheduler noop registered
[    0.920000] io scheduler anticipatory registered
[    0.920000] io scheduler deadline registered
[    0.930000] io scheduler cfq registered (default)
[    0.950000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.960000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[    0.980000] brd: module loaded
[    0.990000] loop: module loaded
[    1.000000] ox820sata: OX820 sata core.
[    1.000000] scsi0 : oxnassata
[    1.000000] scsi1 : oxnassata
[    1.010000] ata1: SATA max UDMA/133 irq 50
[    1.010000] ata2: SATA max UDMA/133 irq 50
[    1.020000] ox820sata: reseting SATA core
[    1.540000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.540000] ata1.00: ATA-9: ST3000DM001-1CH166, CC27, max UDMA/133
[    1.550000] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    1.560000] ata1.00: configured for UDMA/133
[    1.560000] ox820sata: reseting SATA core
[    2.280000] ata2: SATA link down (SStatus 0 SControl 300)
[    2.280000] scsi 0:0:0:0: Direct-Access     ATA      ST3000DM001-1CH1 CC27 PQ: 0 ANSI: 5
[    2.290000] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[    2.300000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    2.300000] sd 0:0:0:0: [sda] Write Protect is off
[    2.310000] tun: Universal TUN/TAP device driver, 1.6
[    2.310000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.310000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.310000] Start USB clocks
[    2.310000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[    2.310000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
[    2.340000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[    2.350000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.360000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[    2.360000] usb usb1: configuration #1 chosen from 1 choice
[    2.360000] hub 1-0:1.0: USB hub found
[    2.360000] hub 1-0:1.0: 2 ports detected
[    2.360000] Initializing USB Mass Storage driver...
[    2.360000] usbcore: registered new interface driver usb-storage
[    2.360000] USB Mass Storage support registered.
[    2.360000] usbcore: registered new interface driver ums-alauda
[    2.360000] usbcore: registered new interface driver ums-datafab
[    2.360000] usbcore: registered new interface driver ums-freecom
[    2.360000] usbcore: registered new interface driver ums-isd200
[    2.360000] usbcore: registered new interface driver ums-jumpshot
[    2.360000] usbcore: registered new interface driver ums-sddr09
[    2.360000] usbcore: registered new interface driver ums-sddr55
[    2.360000] usbcore: registered new interface driver ums-usbat
[    2.360000] mice: PS/2 mouse device common for all mice
[    2.360000] md: linear personality registered for level -1
[    2.360000] md: raid0 personality registered for level 0
[    2.360000] md: raid1 personality registered for level 1
[    2.460000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    2.470000] TCP cubic registered
[    2.480000] NET: Registered protocol family 17
[    2.480000]  sda:
[    2.510000] Alternate GPT is invalid, using primary GPT.
[    2.520000]  sda1 sda2
[    2.520000] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.530000] md: Waiting for all devices to be available before autodetect
[    2.540000] md: If you don't use raid, use raid=noautodetect
[    2.540000] md: Autodetecting RAID arrays.
[    2.560000] md: Scanned 1 and added 1 devices.
[    2.570000] md: autorun ...
[    2.570000] md: considering sda1 ...
[    2.570000] md:  adding sda1 ...
[    2.570000] md: created md0
[    2.580000] md: bind<sda1>
[    2.580000] md: running: <sda1>
[    2.580000] md0: detected capacity change from 0 to 21474770944
[    2.590000] md: ... autorun DONE.
[    2.590000] RAMDISK: gzip image found at block 0
[    2.680000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
[    2.830000] usb 1-1: configuration #1 chosen from 1 choice
[    2.830000] scsi2 : SCSI emulation for USB Mass Storage devices
[    3.260000] VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: root=/dev/md0 console=ttyS0,115200 elevator=cfq mem=256M poweroutage=yes mac_adr=0x00,0xd0,0xb8,0x19,0x4d,0x36
Start Blinking Power LED
USB Device node is /dev/sdb1
Started
/dev/buttons file does not exist creating it
Opened /dev/buttons with fd 3
The Button ID from drive is 2 state is 2
Reset Button is pressed
Checking to see the if the reset button is pressed or not
Checking if there is an attached EMC Imager
[    7.850000] scsi 2:0:0:0: Direct-Access     ClvrStuf USB Flash Drive  6.50 PQ: 0 ANSI: 0 CCS
[    7.860000] sd 2:0:0:0: [sdb] 1970175 512-byte logical blocks: (1.00 GB/961 MiB)
[    7.870000] sd 2:0:0:0: [sdb] Write Protect is off
[    7.870000] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.880000] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.890000]  sdb: sdb1
[    7.890000] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.900000] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[   13.390000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Checking for pre-image script... none.
Image tar file found: /usb_drive/emctools/hmnhd_images/*.tgz
Extract Image tar file.
apps
apps.md5
config
config.md5
initrd
initrd.md5
oem
oem.md5
stage1.wrapped
stage1.wrapped.md5
u-boot.wrapped
u-boot.wrapped.md5
zImage
zImage.md5
apps is valid
config is valid
initrd is valid
zImage is valid
Found EMC Imager with apps and config image...
Started USB Imaging...
[  433.430000]  md0: unknown partition table
  1 logical volume(s) in volume group "md0_vg" now active
Going to do a full install
Reading the old environment values
16+0 records in
16+0 records out
[  433.920000] md: md0 stopped.
[  433.920000] md: unbind<sda1>
[  433.950000] md: export_rdev(sda1)
mdadm: stopped /dev/md0
---Creating partitions
32+0 records in
32+0 records out
Information: You may need to update /etc/fstab.

Information: You may need to update /etc/fstab.

Information: You may need to update /etc/fstab.

---Writing bootrom directions
dd: can't open 'usb_drive/bootrom.txt': No such file or directory
---Writing hidden sectors
17+1 records in
17+1 records out
202+1 records in
202+1 records out
4275+1 records in
4275+1 records out
5444+1 records in
5444+1 records out
17+1 records in
17+1 records out
202+1 records in
202+1 records out
4275+1 records in
4275+1 records out
16+0 records in
16+0 records out
[  439.080000] md: bind<sda1>
[  439.080000] md0: detected capacity change from 0 to 21474770944
mdadm: array /dev/md0 started.
[  439.110000]  md0: unknown partition table
  /dev/sda2: open failed: No such device or address
  WARNING: Forcing physical volume creation on /dev/md0 of volume group "md0_vg"
  Physical volume "/dev/md0" successfully created
  /dev/sda2: open failed: No such device or address
  Volume group "md0_vg" successfully created
  Logical volume "BFDlv" created
mke2fs 1.41.3 (12-Oct-2008)
ext2fs_check_if_mount: No such file or directory while determining whether /dev/md0_vg/BFDlv is mounted.
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
262144 inodes, 1048576 blocks
52428 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=1073741824
32 block groups
32768 blocks per group, 32768 fragments per group
8192 inodes per group
Superblock backups stored on blocks:
        32768, 98304, 163840, 229376, 294912, 819200, 884736

Writing inode tables: done
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 24 mounts or
180 days, whichever comes first.  Use tune2fs -c or -i to override.
  1 logical volume(s) in volume group "md0_vg" now active
Copied apps config and oem image
BusyBox v1.9.2 (2012-03-13 13:29:58 EDT) multi-call binary

Usage: cp [OPTION]... SOURCE DEST

Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY

Options:
        -a      Same as -dpR
        -d,-P   Preserve links
        -H,-L   Dereference all symlinks (default)
        -p      Preserve file attributes if possible
        -f      Force overwrite
        -i      Prompt before overwrite
        -R,-r   Recurse directories
        -l,-s   Create (sym)links

BusyBox v1.9.2 (2012-03-13 13:29:58 EDT) multi-call binary

Usage: cp [OPTION]... SOURCE DEST

Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY

Options:
        -a      Same as -dpR
        -d,-P   Preserve links
        -H,-L   Dereference all symlinks (default)
        -p      Preserve file attributes if possible
        -f      Force overwrite
        -i      Prompt before overwrite
        -R,-r   Recurse directories
        -l,-s   Create (sym)links

4275+1 records in
4275+1 records out
5444+1 records in
5444+1 records out
Remove the temp folder.
Imaging Successful. Please remove the USB drive before the next power on


Then when I reboot, no output to the serial and after a few seconds the HDD spins down and the red light comes on.
Tried it with a small Hdd (250 Gb) and same thing.


Top
 Profile  
 
PostPosted: Wed Jan 07, 2015 12:58 pm 
Offline

Joined: Wed Jan 07, 2015 12:47 pm
Posts: 6
May have solved my own problem.

The bootrom.txt needs to be in the Root of the USB drive.

The diagram on the Wiki isn't too clear.

We'll see, another 10 Minutes write/install to go.

And it seems to work :D


Last edited by Ken555 on Wed Jan 07, 2015 1:17 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Wed Jan 07, 2015 1:16 pm 
Offline

Joined: Wed Jan 29, 2014 6:03 pm
Posts: 86
why don't you install debian wheezy and go for OMV instead?
http://forum.nas-central.org/viewtopic.php?f=269&t=13953
http://forum.nas-central.org/viewtopic.php?f=269&t=6277
http://forums.openmediavault.org/index.php/Thread/5302-Howto-install-OpenMediaVault-on-Debian-7-x-Wheezy/


Last edited by ptelleria on Wed Jan 07, 2015 1:21 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Wed Jan 07, 2015 1:18 pm 
Offline

Joined: Wed Jan 07, 2015 12:47 pm
Posts: 6
ptelleria wrote:


1st stage was to get it working.

Quite like the "copy job" options on the Nas, can OMV support this ?

i.e. copy from a windows share to the nas on a schedule


Top
 Profile  
 
PostPosted: Wed Jan 07, 2015 1:23 pm 
Offline

Joined: Wed Jan 29, 2014 6:03 pm
Posts: 86
Quote:
Quite like the "copy job" options on the Nas, can OMV support this ?

i.e. copy from a windows share to the nas on a schedule

yes, you can create an rsync job for backups (or from windows, a robocopy job) from the web client (but far better create a linux script to handle it, its quite straightforward). i use OMV (and a 2nd HD) for backups (and testing with Amazon Glacier from the HMNHDCE with Linux, which is the advantage over the stock firmware)


Top
 Profile  
 
PostPosted: Sat Jan 10, 2015 10:48 pm 
Offline

Joined: Fri Jun 28, 2013 8:59 pm
Posts: 8
Ciao,
dove posso scaricare bootrom.txt per Windows ?

Vi ringrazio
Roberto


Top
 Profile  
 
PostPosted: Mon Jan 19, 2015 4:27 pm 
Offline

Joined: Tue Dec 30, 2014 9:53 pm
Posts: 34
Ciao Roberto,
Ecco:

Code:
perl <<EOF > /mnt/hmnhdce-recover/bootrom.txt
      print "\x00" x 0x1a4;
      print "\x00\x5f\x01\x00";
      print "\x00\xdf\x00\x00";
      print "\x00\x80\x00\x00";
      print "\x00" x (0x1b0 -0x1a4 -12 );
      print "\x22\x80\x00\x00";
      print "\x22\x00\x00\x00";
      print "\x00\x80\x00\x00";
EOF


Copy/paste il bootrom.txt, pronto!

Saluti.


Top
 Profile  
 
PostPosted: Mon Jan 19, 2015 7:07 pm 
Offline

Joined: Fri Jul 13, 2012 8:12 am
Posts: 110
No, that's wrong. Correct way is to just download it - the link is in the Wiki article!! Creating it with the Perl script is totally unnecessary.

Stefan


Top
 Profile  
 
PostPosted: Thu Apr 02, 2015 9:17 pm 
Offline

Joined: Thu Apr 02, 2015 9:03 pm
Posts: 1
Hi all.
During software upgrade recommended by the manufacturer drive was stopped working. I think software was broken or something. Red lamp is blinking and after few minutes my Iomega is rebooting. DHCP not working. There was a lot of important shared files for me :(

My question is, is it enough to upload the new bootloader, kernel, initrd or must do repartitioning whole disc and restore firmware ?
Maybe You knows another method to access my files ??? When trying to connect HD to computer with Windows or Linux see only GPT partitions and its no possible to read it :(

My IOMEGA is HMND2 - 1TG


Top
 Profile  
 
PostPosted: Fri Jun 05, 2015 6:36 pm 
Offline

Joined: Fri Jun 05, 2015 6:31 pm
Posts: 2
Also does anyone know what the max hard drive that can be used with this system is? Can I install a Western Digital 6TB in this puppy?

Thanks in advance.

Edit:

Does the partition table (I think that's what its called) need to be set as a master boot record or GUID?

Answer = GUID


Last edited by duke69111 on Wed Jun 17, 2015 6:39 pm, edited 2 times in total.

Top
 Profile  
 
PostPosted: Sat Jun 06, 2015 11:31 am 
Offline

Joined: Wed Jan 29, 2014 6:03 pm
Posts: 86
omen1975 wrote:
Hi all.
During software upgrade ....
Maybe You knows another method to access my files ??? When trying to connect HD to computer with Windows or Linux see only GPT partitions and its no possible to read it :(
My IOMEGA is HMND2 - 1TG

Careful, this thread is fo the HMNHDCE: Cloud Edition, different software.
However, in Windows you'll never see the data partition.
In Linux, follow:
viewtopic.php?f=269&t=5253


Top
 Profile  
 
PostPosted: Wed Aug 26, 2015 2:18 pm 
Offline

Joined: Fri Feb 07, 2014 8:10 pm
Posts: 21
giving feedback:
successfully installed a new drive on a dead home media center CE (HMNHD2) using the wiki(which btw, says HMNHDCE, someone should edit it to add the model number).
After that upgraded firmware manually downloaded from lenovo(the automatic FW version check says no new version incorrectly as the iomega website is no more)


Top
 Profile  
 
PostPosted: Fri Sep 11, 2015 5:26 pm 
Offline

Joined: Fri Sep 11, 2015 5:13 pm
Posts: 2
Hello everyone,
I have an Iomega HMND2 (p/n 31950400) with the disk damaged. :o
I would like to replace the disk with a new blank one. I can follow this guide?
http://iomega.nas-central.org/wiki/Reco ... edia_CE%29

Please help me... :roll:
thanks


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 241 posts ]  Go to page Previous  1 ... 12, 13, 14, 15, 16, 17  Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group