General NAS-Central Forums

Welcome to the NAS community
It is currently Tue Oct 24, 2017 11:18 am

All times are UTC




Post new topic Reply to topic  [ 15 posts ] 
Author Message
PostPosted: Thu Feb 26, 2015 10:39 pm 
Offline

Joined: Thu Feb 26, 2015 10:15 pm
Posts: 14
Hi! I have a Cloudbox white and the hard drive stopped to work. Lost all the data but I had a backup.
The problem is that I've uploaded a uboot from a network space 2 into my cloudbox and now the only thing it does is to blink the front led once (blue) and the ethernet left led once.

I have access to windows, linux and mac os machines. I also have a TTL-232R-3V3-WE usb cable. What's the next step? How can I flash the cloudbox uboot?

What files do I need? I found this: ftp://gpl_source:gpl_source@update.lacie.com/. Any good?

Thanks.


Top
 Profile  
 
PostPosted: Thu Feb 26, 2015 10:49 pm 
Offline

Joined: Wed Mar 18, 2009 11:13 pm
Posts: 773
then you have a problem. if u-boot isn't loaded or corrupt or u-boot for the wrong device there is very little you can do. Think you have two options, use JTAG method, but I have no experience with that and you need special tools. Second option is that it seems that kitkwood based devices from lacie seems to support kwboot
if that works on the cloudbox then you can load a correct u-boot in memory via uart (network interface) and then use that u-boot to put a new u-boot in flash
Here a link to kwboot http://forum.doozan.com/read.php?3,7852,7852

---edit
the problem will be finding a working u-boot version for the cloudbox, you will the one to be loaded via uart and to be loaded to flash, these contain the same image but have different headers


Top
 Profile  
 
PostPosted: Fri Feb 27, 2015 12:19 am 
Offline

Joined: Thu Feb 26, 2015 10:15 pm
Posts: 14
Thanks for your reply.

I believe that when you say uart, you mean the serial port, right? http://lacie.nas-central.org/wiki/Seria ... rk_space_2)

I could get a kwboot copy to work on my mac os. But one of the parameters is the file to upload. The problem relies here. Where can I find these files?

I would like to see this nas up and running again. Doesn't matter if it's Lacie or third party software.


Top
 Profile  
 
PostPosted: Fri Feb 27, 2015 9:25 pm 
Offline

Joined: Wed Mar 18, 2009 11:13 pm
Posts: 773
yes you must load it via the serial port, correct

about the file, yes that is the problem where to find an u-boot for the cloudbox. I think is not available on the internet but I might have a look if in the source codes I have from lacie if the cloudbox is supported. Then I could try to compile it for you


Top
 Profile  
 
PostPosted: Fri Feb 27, 2015 10:00 pm 
Offline

Joined: Wed Mar 18, 2009 11:13 pm
Posts: 773
it is done :D I found the source on the gpl site of lacie and compiled it.

If you sent me you e-mail address (via pm) then I can sent you the kwb files (one for uart boot and one to put in flash). This forum doesn't allow to attach files to posts

u-boot-familybox-revA-2.1.3-uart.kwb
u-boot-familybox-revA-2.1.3-sf.kwb


Top
 Profile  
 
PostPosted: Mon Mar 02, 2015 2:27 pm 
Offline

Joined: Thu Feb 26, 2015 10:15 pm
Posts: 14
So, I got your files. Thank you for that.

Tried a couple of times yesterday on my mac but I was always getting the "xmodem protocol error".
Today I had access to an ubuntu box and I got something out from that thing.
Unfortunately, after all the process, the terminal is stuck and it doesn't accept anything. Any suggestions?
I've tried this uart process with and without a hard drive attached and also with and without the ethernet cable connected. The result is always the same.
Btw, when the terminal hangs, I can hear the hard drive spinning up.

Output:

$ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -b u-boot-familybox-revA-2.1.3-uart.kwb -p

Sending boot message. Please reboot the target...-
Sending boot image...
0 % [......................................................................]
(...)
97 % [......................................................................]
99 % [......................]
[Type Ctrl-\ + c to quit]

_ ____ _
| | __ _ / ___(_) ___
| | / _V | | | |/ _ \
| |__ | (_| | |___| | __/
|____| \__,_|\____|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: familybox REV: 0 LE

U-Boot 1.1.4 (Feb 27 2015 - 22:50:49) Marvell version: 3.6.0 LaCie 2.1.3

U-Boot code: 06000000 -> 0607018C BSS: -> 060BF720

Soc: 88F6192 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz

DRAM (DDR2) CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done


Top
 Profile  
 
PostPosted: Mon Mar 02, 2015 7:34 pm 
Offline

Joined: Wed Mar 18, 2009 11:13 pm
Posts: 773
wow , this good news, it actually loads and start u-boot
I think I know why it is hanging, it is the routine where a call is done to read flash size, we also saw this issue when compiling it for the 2big2, I will sent you this evening a modified version.

almost there


Top
 Profile  
 
PostPosted: Mon Mar 02, 2015 8:10 pm 
Offline

Joined: Wed Mar 18, 2009 11:13 pm
Posts: 773
files sent by mail

if you have the uart running then you can write the sf one to flash by using the command
Code:
bubt u-boot-familybox-revA-2.1.3-sf.kwb

(of course the file must be in the upload directory of your tftp server)
To make this command work you will need to have a tftp server running on your pc and probably set server ip and ip address of the nas
you can do thy using in u-boot the commands (you need to replace 192.168.x.y by actual ip address of the pc running tftp server)
Code:
setenv serverip 192.168.x.y
setenv ipaddr 192.168.x.z

Use for x the same number z must be different from y and ipaddr must an ip that is not in use by another device in your LAN

The bubt command will ask you to overwrite the environment, answer no on that question
After the bubt command has written your u-boot to flash use the command reset in u-boot to reboot the cloudbox


Top
 Profile  
 
PostPosted: Mon Mar 02, 2015 10:21 pm 
Offline

Joined: Thu Feb 26, 2015 10:15 pm
Posts: 14
This was a success!! Thank you very much.

This is the output now:

_ ____ _
| | __ _ / ___(_) ___
| | / _V | | | |/ _ \
| |__ | (_| | |___| | __/
|____| \__,_|\____|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: familybox REV: 0 LE

U-Boot 1.1.4 (Mar 2 2015 - 20:54:23) Marvell version: 3.6.0 LaCie 2.1.3

U-Boot code: 06000000 -> 0607018C BSS: -> 060BF720

Soc: 88F6192 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz

DRAM (DDR2) CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done
[512kB@f8000000] Flash: 512 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
SCSI: Error SCSI Controller (11AB,6121) not found
Net: egiga0 [PRIME]
egiga0 no link
egiga0 no link
egiga0 no link
egiga0 no link
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot: 0

Reset IDE:
Marvell Serial ATA Adapter

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: ST3160215SCE Firm: 3.ACB Ser#: 6RX5RCWA
Type: Hard Disk
Supports 48-bit addressing
Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)
PCIe SATA:ffffffff

Booting Nexus layout from disk 0...
** Bad partition 3 **
Booting Nexus layout from disk 1...
** Bad partition 3 **
Boot Nexus rescue from disk 0...
** Bad partition 2 **
Boot Nexus rescue from disk 1...
** Bad partition 2 **
Booting legacy layout...

** Device 1 not available

** Device 1 not available
Waiting for LUMP (0)


Top
 Profile  
 
PostPosted: Mon Mar 02, 2015 10:26 pm 
Offline

Joined: Thu Feb 26, 2015 10:15 pm
Posts: 14
Since my old hard drive is toast, I'm using a Seagate 160GB.

Tried to recover using Lacie Network Assistant but can't do nothing with it. It seems to me that it's expecting something/some files from the hard drive.

This is the output:

_ ____ _
| | __ _ / ___(_) ___
| | / _V | | | |/ _ \
| |__ | (_| | |___| | __/
|____| \__,_|\____|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: familybox REV: 0 LE

U-Boot 1.1.4 (Mar 2 2015 - 20:54:23) Marvell version: 3.6.0 LaCie 2.1.3

U-Boot code: 06000000 -> 0607018C BSS: -> 060BF720

Soc: 88F6192 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz

DRAM (DDR2) CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done
[512kB@f8000000] Flash: 512 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
SCSI: Error SCSI Controller (11AB,6121) not found
Net: egiga0 [PRIME]
egiga0 no link
egiga0 no link
egiga0 no link
egiga0 no link
Waiting for LUMP (3)
Lump received switching to NetConsole on 192.168.0.204
Uncompressing Linux...................................................................................................................................................................................................................................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14-svn7493 (root@Poutre1_node10_x86_32.lacie.com) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 Fri Oct 17 14:00:51 UTC 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: familybox
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 tftp_server=192.168.0.204 static_addr=192.168.0.250 cap=gpt,lba64
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 249728KB available (9320K code, 371K data, 140K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 25.769946] Console: colour dummy device 80x30
[ 25.769982] Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
[ 26.029962] Mount-cache hash table entries: 512
[ 26.030295] CPU: Testing write buffer coherency: ok
[ 26.032289] NET: Registered protocol family 16
[ 26.034625] Feroceon L2: Enabling L2
[ 26.034665] Feroceon L2: Cache support initialised.
[ 26.035198]
[ 26.035203] CPU Interface
[ 26.035209] -------------
[ 26.035215] SDRAM_CS0 ....base 00000000, size 256MB
[ 26.035230] SDRAM_CS1 ....disable
[ 26.035238] SDRAM_CS2 ....disable
[ 26.035247] SDRAM_CS3 ....disable
[ 26.035255] PEX0_MEM ....base e8000000, size 128MB
[ 26.035271] PEX0_IO ....base f2000000, size 1MB
[ 26.035285] INTER_REGS ....base f1000000, size 1MB
[ 26.035298] NFLASH_CS ....base fa000000, size 2MB
[ 26.035314] SPI_CS ....base f4000000, size 16MB
[ 26.035332] BOOT_ROM_CS ....no such
[ 26.035353] DEV_BOOTCS ....no such
[ 26.035375] CRYPT_ENG ....base f0000000, size 2MB
[ 26.035397]
[ 26.035400] Marvell Development Board (LSP Version KW_LSP_5.0.3)-- familybox Soc: 88F6192 A1 LE
[ 26.035417]
[ 26.035424] Detected Tclk 166666667 and SysClk 400000000
[ 26.037444] Kirkwood PCIe port 0:
[ 26.037452] link down, ignoring
[ 26.046062] bio: create slab <bio-0> at 0
[ 26.046461] SCSI Scattered Spinup: Disabled
[ 26.047044] SCSI subsystem initialized
[ 26.049444] NET: Registered protocol family 2
[ 26.049552] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 26.049790] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 26.049844] Switched to NOHz mode on CPU #0
[ 26.050092] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 26.050219] TCP: Hash tables configured (established 8192 bind 8192)
[ 26.050230] TCP reno registered
[ 26.050527] NET: Registered protocol family 1
[ 30.566392] cpufreq: Init kirkwood cpufreq driver
[ 30.580696] gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initialized
[ 30.582598] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 30.582632] Registering unionfs 2.5.10 (for 2.6.31.14)
[ 30.582944] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 30.583640] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 30.584159] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 30.584706] SGI XFS Quota Management subsystem
[ 30.584742] msgmni has been set to 488
[ 30.584864] alg: No test for cipher_null (cipher_null-generic)
[ 30.584939] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 30.585008] alg: No test for digest_null (digest_null-generic)
[ 30.585078] alg: No test for compress_null (compress_null-generic)
[ 30.593719] alg: No test for stdrng (krng)
[ 30.910064] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[ 31.059014] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 31.059030] io scheduler noop registered
[ 31.059040] io scheduler anticipatory registered (default)
[ 31.059049] io scheduler deadline registered
[ 31.059111] io scheduler cfq registered
[ 31.074675] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 31.075784] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 31.075809] console [ttyS0] enabled
[ 31.477933] brd: module loaded
[ 31.481646] sata_mv sata_mv.0: version 1.28
[ 31.485905] sata_mv sata_mv.0: slots 32 ports 1
[ 31.490957] scsi0 : sata_mv
[ 31.494161] ata1: SATA max UDMA/133 irq 21
[ 31.498597] INIT Marvell Ethernet Driver: mv_netdev
[ 31.503714] Loading Marvell Ethernet Driver:
[ 31.507966] o Cached descriptors in DRAM
[ 31.512079] o DRAM SW cache-coherency
[ 31.515895] o 2 Giga ports supported
[ 31.519628] o Single RX Queue support - ETH_DEF_RXQ=0
[ 31.524839] o Single TX Queue support - ETH_DEF_TXQ=0
[ 31.530046] o TCP segmentation offload (TSO) supported
[ 31.535335] o Large Receive offload (LRO) supported
[ 31.540370] o Receive checksum offload supported
[ 31.545141] o Transmit checksum offload supported
[ 31.550006] o Network Fast Processing (Routing) supported - (Disabled)
[ 31.556674] o Proc tool API enabled
[ 31.560329] o SKB Reuse supported - (Disabled)
[ 31.564927] o SKB Recycle supported - (Disabled)
[ 31.569695] o Rx descripors: q0=128
[ 31.573359] o Tx descripors: q0=532
[ 31.577024] o Loading network interface(s):
[ 31.582526] o register under mv_netdev platform
[ 31.588444] o eth0, ifindex = 2, GbE port = 0
[ 31.593170]
[ 31.593174] Warning: Giga 1 is Powered Off
[ 31.598725]
[ 31.600227] mvFpRuleDb (cd132000): 2048 entries, 8192 bytes
[ 31.605970] console [netcon0] enabled
[ 31.609614] netconsole: network logging started
[ 31.615577] m25p80 spi0.0: mx25l4005a (512 Kbytes)
[ 31.620376] Creating 1 MTD partitions on "spi_flash":
[ 31.625416] 0x000000000000-0x000000080000 : "u-boot"
[ 31.631461] mice: PS/2 mouse device common for all mice
[ 31.636990] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 31.644360] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 31.650215] IRQ 53/rtc-mv: IRQF_DISABLED is not guaranteed on shared IRQs
[ 31.660195] cpuidle: using governor ladder
[ 31.664678] cpuidle: using governor menu
[ 31.668781] Registered led device: familybox:red:fail
[ 31.674240] Registered led device: familybox:blue:sata
[ 31.679633] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 31.686051] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 31.729868] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 31.769866] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 31.809954] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 31.849870] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 31.855859] TCP cubic registered
[ 31.859079] NET: Registered protocol family 17
[ 31.863601] Bridge firewalling registered
[ 31.867600] NET: Registered protocol family 5
[ 31.872185] RPC: Registered udp transport module.
[ 31.876866] RPC: Registered tcp transport module.
[ 31.882686] rtc-mv rtc-mv: setting system clock to 2062-08-14 02:49:01 UTC (2922749341)
[ 32.069860] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 32.149885] ata1.00: ATA-8: ST3160215SCE, 3.ACB, max UDMA/133
[ 32.155613] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 32.239938] ata1.00: configured for UDMA/133
[ 32.244450] scsi 0:0:0:0: Direct-Access ATA ST3160215SCE 3.AC PQ: 0 ANSI: 5
[ 32.253328] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 32.261099] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 32.266682] sd 0:0:0:0: [sda] Write Protect is off
[ 32.271586] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.281180] sda: sda1
[ 32.315528] sd 0:0:0:0: [sda] Attached SCSI disk
[ 32.320164] Freeing init memory: 140K
[ 32.324360] Freeing initramfs memory: 4312K
Entering runlevel base
* Starting mount-base
* Starting parse-cmdline
* Starting get-board-id
* Starting populate-dev
* Starting kmap
Entering runlevel capsule
* Starting network
* Starting ipcommd
* Starting check-capsule
Entering runlevel update-capsule
* Starting start-raid
* Starting assemble-rootfs
mount: can't find /rootfs in /etc/fstab
mount: can't find /rootfs in /proc/mounts
mount: can't find /rootfs in /proc/mounts
mount: mounting /dev/md6 on /rootfs/rw failed: No such file or directory
cp: can't stat '/rootfs/var/.': No such file or directory
cp: can't stat '/rootfs/etc/.': No such file or directory
cp: can't stat '/rootfs/root/.': No such file or directory
mount: mounting /rootfs/rw//var on /rootfs/var failed: No such file or directory
mount: mounting /rootfs/rw//etc on /rootfs/etc failed: No such file or directory
mount: mounting /rootfs/rw//root on /rootfs/root failed: No such file or directory
mount: mounting none on /rootfs/tmp failed: No such file or directory
* Starting update-capsule
ERROR: Abort: nv_data partition /dev/sd?3 is invalid. Please check.
mount: mounting /rootfs/rw on /rw failed: Invalid argument
INFO: * Retrieving
BusyBox v1.19.2 (2014-10-17 11:53:51 UTC) multi-call binary.

Usage: dirname FILENAME

Strip non-directory suffix from FILENAME

tftp: can't open '/rw/capsule/': Is a directory
ERROR: Abort: nv_data partition /dev/sd?3 is invalid. Please check.
/sbin/nexus_update.sh: line 85: arithmetic syntax error
ERROR: Unkown update file format for /rw/capsule
* Stopping assemble-rootfs
* Starting reboot
[ 38.722487] Restarting system.

_ ____ _
| | __ _ / ___(_) ___
| | / _V | | | |/ _ \
| |__ | (_| | |___| | __/
|____| \__,_|\____|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: familybox REV: 0 LE

U-Boot 1.1.4 (Mar 2 2015 - 20:54:23) Marvell version: 3.6.0 LaCie 2.1.3

U-Boot code: 06000000 -> 0607018C BSS: -> 060BF720

Soc: 88F6192 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz

DRAM (DDR2) CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done
[512kB@f8000000] Flash: 512 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
SCSI: Error SCSI Controller (11AB,6121) not found
Net: egiga0 [PRIME]
egiga0 no link
egiga0 no link
egiga0 no link
egiga0 no link
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot: 0

Reset IDE:
Marvell Serial ATA Adapter

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: ST3160215SCE Firm: 3.ACB Ser#: 6RX5RCWA
Type: Hard Disk
Supports 48-bit addressing
Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)
PCIe SATA:ffffffff

Booting Nexus layout from disk 0...
** Bad partition 3 **
Booting Nexus layout from disk 1...
** Bad partition 3 **
Boot Nexus rescue from disk 0...
** Bad partition 2 **
Boot Nexus rescue from disk 1...
** Bad partition 2 **
Booting legacy layout...

** Device 1 not available

** Device 1 not available
Waiting for LUMP (0)


Top
 Profile  
 
PostPosted: Mon Mar 02, 2015 10:29 pm 
Offline

Joined: Thu Feb 26, 2015 10:15 pm
Posts: 14
Is it possible to have the original/factory software from Lacie running again?

Or should I go for a third party firmware?

To prevent any other disasters, can you point me what should I use?


Top
 Profile  
 
PostPosted: Mon Mar 02, 2015 10:44 pm 
Offline

Joined: Wed Mar 18, 2009 11:13 pm
Posts: 773
:D ,nice to read that it worked ! so we got it working again, did you already wrote the new u-boot to fllash ?

firmware, well I am a little biased on that point, we wrote our own (fvdw-sl, you can find it on http://plugout.net)
We wrote it because to our opinion the lacie firmware has limited features.


Top
 Profile  
 
PostPosted: Mon Mar 02, 2015 10:59 pm 
Offline

Joined: Thu Feb 26, 2015 10:15 pm
Posts: 14
Yes, I did. The first output was after the reset command.

Yes, Lacie software was limited. I'll give fvdw-sl a go, then.


Top
 Profile  
 
PostPosted: Wed Dec 30, 2015 7:48 am 
Offline

Joined: Tue Dec 29, 2015 10:00 pm
Posts: 1
fvdw wrote:
it is done :D I found the source on the gpl site of lacie and compiled it.

If you sent me you e-mail address (via pm) then I can sent you the kwb files (one for uart boot and one to put in flash). This forum doesn't allow to attach files to posts

u-boot-familybox-revA-2.1.3-uart.kwb
u-boot-familybox-revA-2.1.3-sf.kwb


i have the same problem with 5big network v.1
Is possibile restore it?
Where i find the u-boot file for 5big?
Thanks.


Top
 Profile  
 
PostPosted: Wed Dec 30, 2015 10:07 am 
Offline

Joined: Wed Mar 18, 2009 11:13 pm
Posts: 773
probably not
If u-boot is dead then the solution used on the cloudbox will not work as 5big1 doesn't support kwboot
Further we need the source code of u-boot running on a 5big1 incl dram addresses to be able to try to compile it
But as said even if you have u-boot image then there is no easy way to get it on your nas, you will then need to go the JTAG route (google is your friend) which is not easy


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 15 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group