General NAS-Central Forums

Welcome to the NAS community
It is currently Thu Sep 21, 2017 8:35 am

All times are UTC




Post new topic Reply to topic  [ 12 posts ] 
Author Message
 Post subject: Red light
PostPosted: Sun Jan 12, 2014 9:11 pm 
Offline

Joined: Tue Dec 31, 2013 3:37 pm
Posts: 7
I have two devices both red light flashing

can anybody help me ? (I have basic knowledge on linux)

first one Iomega Home Media Network Hard Drive Cloud Edition 1TB
I stuck on this : zcat Iomega-HMNHD-CE-1st-32M.img.gz | dd of=/dev/sdX bs=1M
I got message no such directory zcat ....


second one Iomega StorCenter ix2-200 2x2TB
I know one of hdd its damage
but my question is can I run on one hdd? or I must have two same hdd?
if I can run on one how I can make recovery

I know its lots questions

thanks


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Sun Jan 12, 2014 9:23 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6039
zcat combines the function of gunzip and cat. The command 'zcat Iomega-HMNHD-CE-1st-32M.img.gz | dd of=/dev/sdX bs=1M' can be replaced by
Code:
cat Iomega-HMNHD-CE-1st-32M.img.gz | gunzip | dd of=/dev/sdX bs=1M


Almost all 2 disk NASses, including the ix2-200, can run fine on only one disk. But if you had a 2 disk JBOD or raid0 system, and one disk died, your data is lost, and you'll have to re-arrange the data volume.


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Sun Jan 12, 2014 9:31 pm 
Offline

Joined: Tue Dec 31, 2013 3:37 pm
Posts: 7
@Mijzelf thanks for quick reply!

Quote:
Almost all 2 disk NASses, including the ix2-200, can run fine on only one disk. But if you had a 2 disk JBOD or raid0 system, and one disk died, your data is lost, and you'll have to re-arrange the data volume.


I know one hdd its 100% died not starting
Can u tell me how to make recovery on this second disc ?
thanks


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Sun Jan 12, 2014 9:35 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6039
I don't understand. If you had an ix2-200 which worked, and after that one disk died, it should still work on the remaining disk. So why do you need recovery?


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Mon Jan 13, 2014 5:07 am 
Offline

Joined: Tue Dec 31, 2013 3:37 pm
Posts: 7
No no ix 2-200 not working at all red light flashing i just checkt both hdd on PC -linux one its
broken cant read nothing second working.
I have both NAS from second hand so i got no idea what's happened.


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Mon Jan 13, 2014 10:22 am 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6039
Here is the recovery file for the ix2-200 CE. Unzip it to a FAT formatted USB stick, of at least 1GB.

If it doesn't work, you probably have a 'classic' ix2-200. Then you'll have to rename a directory. The stick contains a directory emctools/XX200dYY/, where I can't remember the values for XX and YY. 200d has to be renamed to 200, or the other way around.
You'll have to apply the stick, then rename the directory back, and apply it the second time. The first time will flash a new kernel (and turn the box in a CE), the second time will format the disk.


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Mon Jan 13, 2014 3:48 pm 
Offline

Joined: Tue Dec 31, 2013 3:37 pm
Posts: 7
Mijzelf thanks for quick reply!

Ok I done full recovery procedure on Iomega

Power off HMNHDCE by pulling the power cord.
Put the prepared USB-Stick in.
Press and hold Reset-Button while plugging in power cord (refer to [picture], use a needle or similar tool).
Release the button when the activity LED of the USB-Stick starts to flicker.
Wait until HMNHDCE powers down on its own.
Pull the stick.
Pull the power cord and reattach it to reboot.
NAS starting and after moment start red light lighting

no access by web just nothing ...



Thanks


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Mon Jan 13, 2014 6:29 pm 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6039
You did not use the ix2-200 usb stick in combination with the Iomega-HMNHD-CE-1st-32M.img.gz, did you?

The disk is not initialized right. The 900+GB unpartitioned space should have had a partition on it, so somehow the initial setup failed. You can try to offer the usb stick a 2nd time. If that doesn't work you can try another usb stick, and if that doesn't work you'll need to hook up a serial port, I'm afraid.


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Mon Jan 13, 2014 6:44 pm 
Offline

Joined: Tue Dec 31, 2013 3:37 pm
Posts: 7
Mijzelf wrote:
You did not use the ix2-200 usb stick in combination with the Iomega-HMNHD-CE-1st-32M.img.gz, did you?

The disk is not initialized right. The 900+GB unpartitioned space should have had a partition on it, so somehow the initial setup failed. You can try to offer the usb stick a 2nd time. If that doesn't work you can try another usb stick, and if that doesn't work you'll need to hook up a serial port, I'm afraid.




No i use Recovery (Home Media CE)


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Mon Jan 13, 2014 7:34 pm 
Offline

Joined: Tue Dec 31, 2013 3:37 pm
Posts: 7
I try 4-5 times and have same effect so what wrong ? hdd? or ?
Thanks


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Tue Jan 14, 2014 9:37 am 
Offline

Joined: Mon Jun 16, 2008 10:45 am
Posts: 6039
Don't know. Do you have a reason to suspect the disk? In that case I'd concentrate on that. And else, well, you'll need a serial connection.


Top
 Profile  
 
 Post subject: Re: Red light
PostPosted: Tue Jan 14, 2014 7:58 pm 
Offline

Joined: Tue Dec 31, 2013 3:37 pm
Posts: 7
No I not really suspect disc
I got this disc from second hand and working but not really good when I try add user or something else shows The selected function is not available due to the state of the pools.
So I try make recovery but not help so I format this disc on windows try use like normal disc and working fine
so I try make full recovery but not working


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 12 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group