So, the console is J4:
1 GND
2 Rx
3 Tx
4 nc?
5 nc?
6 +3.3V
This is how does it boot with ethernet cable connected:
Code:
ROM Code Running
halSPI_ProtectStatus_Clean,status = 0x0
INI_ROM_ON_FACTORY_TEST_MODE = 0x3
JM2357_SPI_FLASH_ID = 0x3267ACE9
0x31373533
The spi_flash_id = 0x3267ACE9
0x31373533
Normal Mode Will Jump to SRAM
The DDR Train at spi addr = 0x1000
The DDR Train at Sram addr = 0xB0004000
image_len = 0x8C0
ASIC_300M_CLOCK DDR init
ASIC_300M_CLOCK DDR1
DDR IF reset
0xb8000c20 = 0x2
0xb8000c24 = 0x8131
0xb8000c28 = 0x22220342
0xb8000c2c = 0x20E56
0xb8000c30 = 0x10200080
0xb8000c34 = 0x1177
0xb8000000 = 0x1
0xb8000004 = 0x73
0xb8000008 = 0x0
0xb800000c = 0x0
0xb8000010 = 0x0
0xb8000014 = 0x0
0xb8000018 = 0xE0E
0xb800001c = 0x0
0xb8000020 = 0x0
0xb8000024 = 0x40010842
0xb8000028 = 0x0
0xb8000030 = 0x0
Das firmware Image at spi_addr = 0x18C0
Das firmware will loading to currentDDRaddr = 0x20000000
Das firmware image size = 0x7B18
-=========================================-
Boot Loader [LOADER 1.04V]
Press <ESC> to enter extra mode
-=========================================-
Vendor ID : 8c, Device ID : 2115
Default MAC: 00:11:22:E5:EA:93
Default IP: 169.254.0.1
Initialize MAC & PHY... PHY_ADDRESS = 0x1, Broadcam's PHY
PHY link is UP, work on 1000Mbs, FULL Duplex
Start Decompress Kernel.............................................................................OK
Jump to kernel...
==========================================
CodeTek JCS358 [LanDisk] JCS358E-1.04s
Hardware Version : 0000 Speed 300MHz
==========================================
System running!....
Vendor ID : 8C, Device ID : 2115
ESMT F25L16QA (2MB)
SATA: RAID mode enable.
WebDAV: use SMB's CFG.
FTPS: use SMB's CFG.
GPIO_MODE: Set to 0 mode.
Vendor_VID: terra-master
SYS_LoadVendorConfig: WEBRD "www.mydisk.biz"
TCP/IP initialized
PPP: initial ok.
4 LED Mode
TCP/IP Start
SEARCH_Task(): SEARCH Initial done.
HTTPS_Task(): initial done, port:8000 eport:8000.
DAV_Task: WEBDAV 8088 /webdav initial OK.
Line print server listening at port 515...
SATA0 Phy has been detected
ATA Initialize!
1 IDE devices attached at [ide]
HD Model: HITACHI HDS7225SCSUN250G 0713BE4WRK
JM390: detect OK, FW 9.88.
FAT64 initial done.
SMB_Task(): SMB Initial done.
TX Descriptor DMA Start: 0x40008040
RX Descriptor DMA Start: 0x40008840
PHY ID: 0x362, Model: 0x5E61
PHY link is UP, work on 1000Mbs,FULL Duplex
eth0 link up
MAC Addr: 00:11:22:E5:EA:93
UPNP_PM_Init: updTime 10 min, initial ok.
CMD>ITUNES_Task: Initial done.
SOAP_Task(): SOAP Initial done.
<UPNP> UPNPAV is UP.
UPNP_Task(): UPNP AV Initial done.
BTS_MainTask_Init: init BT OK.
Current interface port0!
DHCPC: Bind IP (192.168.1.130) OK.
...UPNP_PM: Service not found 1!
UPNP_PM: Service not found 2!
UPNP_PM: Service not found 3!
UPNP_PM: Service not found 4!
UPNP_PM: Service not found 5!
WEBRD_Update: fail.
I have not been able to break the boot process yet (pressing ESC does not work for me for some reason) nor get some kind of login prompt once the boot is done.
Login
Register
FAQ
Search
